spec

Does anyone have this torque spec? I can't seem to find it. Thx.

Selling a set of the bling wheels that came stock on my Euro Spec FE570, with the high end 7000 series blue aluminum DID Dirt Star rims and turned hubs with a polished silver look. Stock enduro sizes, 21"x1.6" in the front and 18"x2.15" in the rear. The sprocket is a 50T. The rear was removed...

Does anyone know the proper weight reject specification for the float in a Keihin FCR MX 41, which my 2007 FE550e came with? Or perhaps some kind soul has a new one and will weigh it and reply? I am used to defining float serviceability reject criteria by weight, as per...

Hi all, I'm trying to figure out a good battery solution. I'd like to try to understand the power spec and real-world power usage of the electric starter. It looks like the starter only pulls 50A max? I'm not sure though!: The 2012 570 manual specifices a "E-START. ENGINE CPL. 0,45KW...

2006 FE550. Time to check the valves. Does anyone know the actual clearances for the intake and exaust valves? I know about the 1/6 turn thing, I just have a hard time believing that the intake an exaust operate at the same temperature. Mabe I'm wrong. Someone please enlighten me. Thanks

'06 628cc cam marked 820-08. 5/2522 Can anyone give me the spec for this cam? We're looking for valve lift, timing etc. Need as much info as possible to match gas flow with oversize valves. Many thanks

As above the full spec can be found on eBay with the link below. I've have husabergs for years and this was the last bike I had it was bought as a new bike in 09 min the engine as it was removed for a side car project, all the preformance parts I've had over the years are fitted to it. If it...

Dear members just a quick plug for some excellent service. Ordered a pair of Golden tyre 216's from Dirt Bike spec on Wednesday night and they arrived this morning (Friday)The company is run by Paul Bolton of extreme enduro fame. Just wondering about ordering some tubliss but not many people run...

Does anyone know the head torque for a 2010 FE 390 and will the head come off in the chassis ? or do i have to remove it Thanks in Advance Stan

I have been trying to get the front end on my 08 550FE sorted and after doing research have concluded the factory spec sheet is incorrect. it calls for spring length of 485MM which is the correct length is 505mm and the spec sheet says tube length is 549mm which it is actually 577mm. My bike...

hi all, on the side of my exhaust it says spec, is this the standard exhaust ?

I've heard mention of updated maps being available for the FE 390 & have asked my Dealer a couple of times. I Keep getting told that there isn't anything for them. Is there anyone with a Aus Spec bike that has had updated maps installed? Thanks

I searched I swear! :D Would anyone happen to have the torque spec for the clutch center nut for the FE390? Thanks for any scoop! Lee

Hi there, don't suppose anyone out there knows what the valve protrusion/ installed valve height spec is for the 2000- 2003 Fe 400's? I've searched through all the official literature, the doc and the forums to no avail. Cheers, J. Fe400 bitsa 2001-2003.

Need the jetting for FE650 -05 for full Titan Akrapovic Exhause system does anyone knows what the recomendation is. The file on the page does not work Thanks Macke

Hi all, I currently have a front rim (1.60 ) and hub to be reassembled on an 03 FE650. As it will be sent off to a shop as I dont have time, I need to furnish the guy with the offset spec for correct alignment. Does anyone have the dimension from edge of rim (widest part) to outer edge of...

Does anyone know where or how to get the sparky insert for the Akrapovic mufflers that are on the 08 US Spec bikes? I hope to go to the 1st 2 AMA National Enduros this winter and a USFS approved sparky is a must. I have a new take-off Husaberg muffler from an 07 but I want to use the...

WERA (an American club racing sanctioning body) in conjunction w/ the AMA has announced a preliminary set of rules for a spec racer class for the 2008 season. The class is based on 400-450cc motocross/enduro bikes modified for use on road courses. Details can be found here: Link to WERA...

I was just reading the 08 HSB specs and see that they just changed the website from a week or 2 ago. Now the website says that the US and Australian FEs still come with the old 10.5L tank and the EU models come with the 7.5. WTF?? I am kind of bummed.

is it possible to upgrade 04 FS650e to FS650e 07 spec? is it possible to upgrade mechanically with the engine changes?