solution

Righto, so finally have the bike together and running again after installing my Kibblewhite dual valve springs (Thanks for all the advice via PMs Bushy!) I thought I had this job done a couple of weeks back only to realise that the bloody kickstart mech had jammed! Sounds like this a common...

Anyone knows of a good (tested?) solution to get rid of the blinkers on a 2011 FS 570? * Smaller indicators that would fit on the original spots? * Integrated with tail light? I browsed the net but only found 'generic' tail lights which I don't know how they'd fit and look on the FS. I'd...

Hi all, after asking, searching Everywhere, I've found the FINAL SOLUTION for the VAPOR LOCK ISSUE affecting many HUSBY lovers.... you need to check the gap of the pick-up of the start (accensione in Italian) if this pick-up gap is not well regulated the engine stops and has incredible...

Wonder why nobody thought of this before?, Here's a solution to all the controversy over full-body scanners at the airports:, All we need to do is develop a booth that you can step into that will not X-ray you, but will detonate any explosive device you may have hidden on or in your body. The...

Does anyone have a way to carry drinking water that doesn't involve carrying it on your back (Camelback)? My back doesn't like carrying the camelback, and it pulls the chest protector back into an uncomfortable position. So, maybe a fannypack with a water hose, or soft bag that would strap...

I have to admit that the solution mount thing cleans up the cluster of cables, especially on a dual sported bike, BUT... it is not very solid, Mr Cycra! I had a very little washup in the sand, I did not even stall and left right away, except the handguard was point way up. I could not bend it...

I have Cycra handguards on my Berg, but the way I like to have by clutch lever and the cup, the cable touches the guard mount and it's not super duper. Believe it or not but I do fall (seriously I have been falling very little with the Berg compared to the DRZ, just that one fall happened...

It is certainly a design fault for this bike to get water in the carb boot each time I wash it. I want to find a way to prevent the air filter getting wet . After washing when I check the air filter I see that almost every part of it is saturated with drops ready to be sucked to the carb (...

I don't like carrying luggage on my backpack so I tried to fit a tankbag to the rear subframe of my bike. If there is a way to fit side cases to this bike for trips or any other method to carry luggage I would be glad to learn.. thanks.. here are some photos of mine

well i have just taken stock of a lineweaver needle that i asked dale to machine to a spec i wanted to try and after a test i am having my engineer modify it some more. the bike likes a lower MJ and i have now fitted a #145. the next test is to borrow scoots 41mm carb and do a back-to-back...

I am messing with the idea of retrofitting a japanese( I hope that is not a dirty word) ignition for older Bergs to replace the SEM at time of failure. My idea would involve making up a complete package, stator, flywheel, wiring and instructions all in one kit. I am just getting started with...

Well not exactly. This e-start question comes up time and time again and will not go away. It is like a plague. A zit that can't be popped (sick). Currently our friend Mr. Lefrogg is pulling his hair out. Next week it will be someone else. The path of least resistance is to blame the battery...

First of all hello folks this will be my first post here. I had a curious problem with a 450 enduro bike. Once warm it would stall from idle if you tried to accel suddenly. One or two little blips and it would not pick up, just chuck it. Easy opening of the throttle would not cause this. It...

Me and my bud want to set up one of our bikes for supermoto, the main investment is obviously the wheels, and since his KTM is an 04 it has the 26mm axle on the front and my berg has the 20mm. we can only afford one set of wheels so we have been trying to decide which one we buy the wheels for...