slow

HI I own a 2009 Fe450 - it will not start off the Estart - I used to but now no good - can drop stop it fine - have checked the decomp and its seem to be working fine - valve clearances are inlet 0.11mm / exhaust 0.14mm - have put brand new battery in it (170CCA) - no change ? - have tried...

My 2010 fe450 starts ok from cold. If I stop briefly or stall whilst out and hit the starter it fires up. If I stop for a break or 're fuelling for a few minutes it cranks real slow and won't start. It will bump start straightaway and runs fine. If I wait a few more minutes and try it spins...

hi my names luke. so ive got a 2001 400Fe with a 501 engine, (unsure of the year of engine) its not too bad to start on the kick start .. so my problem is with the E start, someone removed the manual decomp lever cable before i owned it) i have re fitted one and set it to what i think is ok, i...

I read a lot of topics about this problem. The starter only just manage to overcome the compression, replaced the battery, checked valves but no solution yet. I read about a batch of decompresion pins(?) which were on the lower limit of specification. When the exhaust valves are on the higher...

Good Evening, I have an issue where my bike is running good (not perfect) but the biggest issue is that it is slow to return to idle...(the bike is 100% std) The bike had been laid up for nearly 8 months while I had a knee reconstruction but I'm now ready to go so I got it out, some fresh fuel...

I have a450 09 i am trying to work out how to adjust the slow an high speed adjustment on the rear shock , can any one tell me when i should be playing with either adjustment thanks

I finally stepped up and picked up a '10 570 from Mark at SOS. When I picked it up, we went to fire it up and load it into the truck and it took quite a bit of spinning to get it started, but I thought well it's new and probably has old gas in it. First thing I did when I got home was removed...

Hey guys Lately I'm only riding when I go out with my wife. she is a beginner and rides slow - very slow. not that I am a pro myself but we usually ride of 2-3 hours and 80% of the time I am in first gear. My questions: 1.How bad is it for the bike? 2.How often should I change the...

2 questions: speedometer tire set at 1790 reading 8km slow? i recently (3 months ago) set my tire size on my speedometer for a 17 supermoto front tire. however, it's reading about 6-8km to slow, which means it's also reading distance at a shorter range than normal. I.E i just traveled with a...

Found this 610cc kit, its for the ktm 530exc but it should be just to drop in the Husaberg :twisted: http://www.thumperstore.com/KTM_530xcwr ... sh-xcw.htm Regards

We went for a wet ride this past weekend and towards the end my bike was cranking very slowly and wouldn't fire. I kick started it with no trouble and rode for another hour or so with no real problems starting with the button again, until this am. She wouldn't start at all. I was short on...

So last week first kick in the morning, my foot slips of the kickstarter and WHACK! the kcikstarter hit the back of my thigh and leaves me a bruise. I think to myself, "that was dumb, don't do that again". This weekend the bike doesn't start first kick, so I kick it again while telling the guy...

So here is my question, following the difficulty I had on Sunday. In normal riding conditions, the engine runs nice. Again, I am so pleased at how regular the power comes, with not nasty hit and simply more and more power available on demand. It is a 2001 FE501e and I had a lot of...

hi gang, I have a new berg now, a 2003 fe 400e, which ran perfectly when i got it - about two weeks ago - i have used it extensively since but one day, poss. after lots of jumping the throttle shutdown became unpredictable and slow, sometimes it shutsdown straight away but most times its revs...

Hi all, Since installing the new follower bearings and new cam chain the starter struggles to turn the motor over. I first thought the valve clearances had loosened due to settling in etc but ther're OK, the only thing that I can think is that the (slightly) different valve timing due to the...

Just finished creating some graphics on the shrouds. They are intended for a yellow / black combination of frame/plastics ; There are also graphics in the same pattern for the rear fender / sidepanels You can view them bigger in my gallery section (739*800) Let me know what you...