seals

Does anyone know what bearings and seals to use for swing arm in a FE400 96 and FC600 99? I have been trying to look in older threads without success.

Looking for seals for 1996 Hsaberg FE501 Where might these be found?

Sorry if I did t search enough. I can’t find any info on reviews for aftermarket fork and dust seals. For both fitment and quality. And is there any suitable replacement for the oem fork fluid? Thanks Edit- I’m speaking in generals but if it helps I’m riding s 2010 450fx. New to the dirt bike...

G'day all. Just changed out both water pump seals, oil/coolant, on my 2009 Fe390. The coolant seal was straight forward but it wasn't quite clear as to wether the oil seal could be replaced without removing the housing. It can be done. Carefully. The oil seal is backed by a bearing so there is...

I'm replacing my 2010 FX450 big end & main crankcase bearings. The manual says to heat the crankcase halves in an oven to 150 degrees C (302 degrees F) and the bearings will fall out. I don't really want to replace transmission or balance shaft bearings as well. Will heating them to this...

Has anyone a list of the bearings and seals needed for the Husaberg rear linkage system? bearings pins seals shoulders and spacers? if I can help you help me etc? let me know if anyone has the dimensions or 'what else they also fit'! I have the actual swing arm bearing...

Hi I have a husaberg supermoto and i want to replace the wheel bearings in the front wheel and rear. i heard a noise and i think that is the problem. I dont know which brand to choose. i found these (moose-all balls-pivot works) does anyone know what brand is the best? i think all balls using...

Well guys, As usual I am looking for parts for my old Berg. I have done surprisingly well. Many shops told me I would not find any parts and others either had the parts or had the generic fix. I am now down to my last bit of items. The hardest one in the 4 valve guide seals for my 1991 fc501...

Hi Guys, I want to order set of japanese good quality sealed bearings for my 2011 FX450, ebay and shops are selling allballs **** and everyone knows how long they last, my rear bearings feel worn but no play there yet and I don't want to take them out and wait with stripped bike for the...

Hey, I'm about to replace seals and oil in my 2011 FE390 front forks for the first time, and I have some questions to the forum- 1. Recommended guide or video? 2. What fork cap tool do I need? A standart KTM will do? 3. Recommended seals? thanks!

I'm getting ready to replace the fork seals on my 2011 FE570S. I've replaced literally hundreds of fork seals in my lifetime, but never the Husaberg seals, so are there any little interesting tricks that I need to know or issues I should be prepared for?

hi guys.i bought my first berg a few wks ago.550fe 2007.but the coolant is coming out the weep hole so i bought the o ring,seal,gasket and bearing.i took all apart today and im havin difficulty getting sorted.can any one tel me exactly watvto do.i have the new bearing in the cover an its sitting...

I've been needing valve seals for my 98 501, and the suppliers I knew of were backordered. It's the only thing my bike has been needing, so I dug into it. My local KTM shop said that LC4 engines use VW Scirocco valve springs, so it got me wondering... I cross referenced the PN on my valve...

Hello all! Just wanted to give a quick report on the Synergy X-Bushing I just installed. Install was very straight forward and the part that took the longest was grinding away to get the proper fit. However, I'm happy to report that for me the combination of the low seat and the x-bushing has...

Hi There, Sorry for the stupid question but I am mildly confused on this one, I have changed many a seal on the KTM RFS engines no problem and figured this was the same, hoping you guys can help me out a little? I did search forum first but not quite getting it. I have a 2010 FE450(and one of...

Finally got some clear weather and some time to go for a squirt. Was out at a local spot fairly blasting around with my brother (roostya) when we came across a pair of CRF-X riders at pace. The first guy came out of a blind corner at pace as well with his buddy in hot pursuit, I had nowhere to...

yep, as the topic says,what brand is best? it seems every expert i talk to ,has a better than stock seal. i know it is pretty hard to get any fork seal to last when you ride it through the mud & crap all the time + the upside down forks don't seem to last like the old right way up forks,but hey...

I have a 'new to me' 08' Husaberg FE 550 with 14.5 hrs on it. It appears to be 'weeping' oil out of what looks like the water pump weep hole. This tells me that my water pump seals might be gone. :( That being said, what is the cross reference to KTM odel (if it is; 530?) for the water...

basic mod to improve the life of your fork seals - cut a bit of foam 10mm x 10mm x 160mm - soak the foam in wd40 - prize out the fork dust wiper seals - install the foam in the small cavity between the fork seal and the wiper seal - install the wiper seal (will be tighter fit now) -...

I am having difficulty installing Synergy fork seals in my White Power 50mm forks http://www.synergyseals.com/. Has anyone used these fork seals before? If installed with the U-Grovve down they seem a little large and won't seat in the fork leg. They would go in with the groove facing up...