roller

Can someone make a recommendation for a chain roller replacement (part number 120 056-01) for my 2002 Husaberg FE650e. I checked with the local KTM dealer and he could not find the part number or my bike. I found plenty online but without measurements I cannot make sure it will fit. Seems...

There is plenty of information throughout this site relating to checking & setting crankshaft end float on 01 to 08 engines but i cant find anything on the 98 to 00 engines where a roller bearing has been retrofitted in place of a ball bearing. It is suggested that axial play on the 01 to 08...

Having learned of the shortfalls for the 01 550 top end I started with the roller rockers. There seems to be two types installed. Don't know which of two prior owners may have upgraded or replaced when failed the roller bearings. Please chime in and share what you identify. The issue being...

Hi, Came back from a trail ride and noticed the upper roller that is sandwiched between the frame and battery basket is missing. No worries, check the manual .... can't find the part on the pages for either battery basket or frame parts. The drawing doesn't show it. There's a part...

Well my 99 FC600 started making a whine in the topend last weekend. Changed the oil today and had a lot of small metal particles in the oil. Pulled the cover off the head and one of my rocker arm rollers was shot, ate up the side of the cam lobe which appears to be where the metal in the oil...

Official Husaberg Bulletin #HB-01-03 Rocker Roller Checks For 2003 Husaberg FE 501/650

my 05 450fe started a strange rumbling sound around clutch. pulled motor down couldn't find anything at the start but found the four small needle roller bearings holding starter gears look fine but when put gear in a turn by hand it sounds like rollers in bearing are square. can anyone give...

2013 FE350 I'm replacing a flywheel which was bent from a rock puncturing my ignition cover. Any hints on removing the roller freewheel bearing pack that fits into the back of the flywheel. It's in there tight. It's super spendy on top of an already expensive repair. Thx!!

Hello my names Alex and a proud owner of my 2003 Husaberg FE 400 E. Ive looked on this forum plenty but have never made and account and needed advise. Me and my dad have taken apart the bike after finding some needle barrings while draining the oil... Seems like the rocker roller barrings are...

Enjoy Looki [vimeo:icep2kby]http://www.vimeo.com/10477143[/vimeo:icep2kby]

After rebuilding my fs650 the gear from fist in second was a bit sharp/rough/jittery/clunky not extreme but just enough to anoying also the shift under light load from 5 to 6 was the same. Pulled it apart to check all was ok and was sure there was a extra washer under the spring shart with small...

Hi Everyone, The saga of my FX 470 rebuild on the cheap continues. I noticed some roughness in the rocker roller bearings and upon inspection found flat spots on both of the central shafts of the bearing. No wear was detected on the needles or outer race. New bearing assys were about $70NZ...

Just curious as to whether this info under common faults in the doc is correct. My inlet roller is on the way out and this looks like a cheap fix but is a ball bearing sufficient as a roller on the end of the rocker ? Cam follower bearings pre '03: They all go eventually. They break up and...

05 FS650E Second time now but at 400 engine hours and 10,000 miles on the clock should I complain? First time was at 176 engine hours and 4600 miles. Bike was running great but I noticed a drastic increase of little silver hairs on the magnetic drain plug. Some additional investigation...

Just started putting my 2002 650 block back together and messed up already :D I switched to roller bearings for the mains, heated up the inner bearing races ( hope this is the word, i mean the inner things on the bearings wich you can remove from the bearing and go on the crank), fitted...

I need new Roller Bearings for the rockerarms for my 2003 FE400e. I was sent updated bearings which do not fit the rockerarms and there seems to be no supply of old style bearings in Australia. Apparently I can purchase the new style rockerarms to take the updated bearing by these are a few...

Hi, I have started to dissemble my engine. When I splitted the engine I found that the right hand main crankshaft bearing is a roller bearing, Japan EC NTN 206ECS46. Shouldn't it be a ball bearing? Didn't checked the left hand due to lack of time but I assume there is a roller bearing as...