replacing

I recently bought a Husaberg fe350 from 2013. The battery that was on the motorcycle was bad. one day I was preparing to go on a ride so I set up the charger to fast charge which fried my ECU, now I have installed a new ECU and a new battery but the ECU is from an sx250, the bike has a hard time...

I'm replacing my 2010 FX450 big end & main crankcase bearings. The manual says to heat the crankcase halves in an oven to 150 degrees C (302 degrees F) and the bearings will fall out. I don't really want to replace transmission or balance shaft bearings as well. Will heating them to this...

Hello, I want to ask if I could change the pump connector Husaberg FX 450 2011 Magura with pump KTM SX 250f 2010 Brembo? Will it work? I am not happy Magura changed entirely in upper pump handle checked whether the lower pump misses everything was fine and still drive like a time waste heat...

Hi! I have a husaberg fe550 -04 and I have a crack in the cylinder liner so I'm going to replace it and the piston.. But since I'm going to disassemble the engine, I was wondering what other parts u customarly replace when doing this type of job? Barrings and so on? I have one other question as...

Gday folks, My hand brake lever nearly pulls into the hand grip. (FE650) it works well, no drama, but such long travel. I have used the black knob there to adjust it out as far as possible, till it fell off doh, its on, but no adjustment left. So what are my options ? Cheers David

I hope I did not but the seal was quite difficult to remove and I was using a offset screwdriver to get behind the metal lip of the seal and pry it out. When I got it out I saw that the brown/yellow plastic piece just in front of the roller bearings had a nick in it. It is not all the way...

Hi guys. Im trying to replace the head stock bearings but can't get the yolks off...what am i doing wrong? I slipped the forks out. Remove head nut and top yolk came off fine but lower 1 dosnt won't to drop out. Could it b seized up?any advise?

I'm getting ready to replace the fork seals on my 2011 FE570S. I've replaced literally hundreds of fork seals in my lifetime, but never the Husaberg seals, so are there any little interesting tricks that I need to know or issues I should be prepared for?

I'm replacing my old kickstarter shaft with a new one. The new axle is the replacement axle (-03 or newer) that Husaberg says should work since the old one is discontinued. Only problem is that the new axle doesn't look the same as the old one and it catches a ledge in the engine case. What to...

Hi, The inevitable happened :( My timing chain on my '07 Fe 550e broke and wedged in somewhere ...I will not disclose how it happend :oops: It has 8000km on and 190 hours. I'm replacing it but would like to know from someone who did it before, if there is an easy way of doing it. I will...

Hey i just bought a dirt tricks camchain tensioner and i need some advice how to install it. Does it require a special tool? Does it matter when i remove the old tensioner, do i have to lock the engine or something? And i suppose i have to lay the bike down and install it collapsed like it said...

Hello. I have a 1992 husaberg fe 350 in which the stator is dead. Now I have quite similar stator from a 125cc aprilia. I measured it and it gives 1,7 kOhm from red to black and 60 Ohm green to black instead of the 23 Ohm it should be. I'm not getting spark with this aprilia's stator and I am...

So because the sun was shining I decided to finally check why the kickstart engages so badly and late in the stroke. Here's what I found... The kickstart gear has some smaller marks from the locking pawl, otherwise it looks fine. Kickstart shaft has some quite big marks. Does it matter that...

I broke my plastic kickstand foot off after being to lazy to lift my bike onto the stand. I was going to replace it with an aftermarket kickstand but no one makes one. I checked the parts diagrams and they list a replacement foot for the oem stand but i don't know how to remove the broken piece...

Anyone experience with replacing the kickstarter axle from a 2003 FC 550? Today i tried to start the FC/FE 550 of a mate and the kickstarter axle broke. Weird experience to encounter. Is it hard to do? Do you have to take the engine out of the frame? It's a strange bike. It has lights and was...

Hi, Am I able to change the seal ring on the secondary shaft(behind the front sprocket) from outside,I mean without splitting the case?

I got some stiffer front springs which included a few shims for proper length.will there be shims under the stock springs ? and if so how would you fish them out? I was hoping to take caps off remove stockers ,confirm oil level,and drop new ones in and be done.

Hi guys, you may be aware that the standard issue spoke nipples on the FS650E SM wheels are plain carbon steel with a paint coating. I had my wheels overhauled recently, and they came back fully re-built, but the company had wire brushed the nipples leaving bare metal exposed (which would...

If my starter keeps not working (for restarts, that is) I may simply remove the battery and the starter motor on my 2001 Fe501e. My issues I think are a worn sprague and the fact that I updated the motor to the 650 model, which may prove too powerful for the old sprague. Updating the...

I bought a fs 650 e and it's set for racing with no wiring onto her. Can anyone assist? I have a full wiring loom, lights battery etc, but no idea where it all goes! Perhaps some photos of your road going bike maybe? Any / all offers greatly received. Thanks Tim