removing

I want to remove the battery and electric start from my 2007 fs 650 since I don't use it on the road anymore. This is where I'm at right now in terms of wires: I'm pretty sure I can simply remove the starter motor, start relay and battery but need to keep the regulator-rectifier since...

Hi guys and gals, I have a 05 FE550 and was doing the water pump seal when I managed to dislocate the kickstarter mechanism. Fixed that no problem by removing and re-installing the clutch, but now my clutch lever is pretty much stuck. I have a Rekluse Z-Start Pro btw, and pretty sure I...

Hi I notice some play in the bottom rear shock absorber fastening. My guess is that the bottom bearing is shot. I have removed the bottom bolt inside the swing arm and the top bolt. The bottom end of the shock is somewhat stuck in the swingarm. So my question is Is there something else that...

How do i get the front fender brace bolt off that bolts it to the front fender? it just wants to spin when i try to unbolt it..

Hi all, Just had the motor out of my 2005 650 to do the timing chain. Put it back together and now there is a moderate leak from the tappet cover. Is there a way to remove it and reseal it with out pulling the motor out again? Any info apreciated. John

I want to completely remove and clean my carbs since my bike runs pretty rough, especially in 1st and second. A lot of back firing, and it actually jerks the bike a bit. Figured I'd start with this. I have the manual that gives me steps but it doesn't show me how to actually take it off the...

Do I need a clutch holder tool to remove the stock clutch basket? Installing a slipper. Anyone know the size of the nut? Says 18mm in the parts manual but I think that is the inside diameter. Thx!

Trying to remove the mid pipe on my 11' 570s so I can get it ceramic coated but for the love of God please tell me I don't have to move or remove the motor! I have removed the head pip, have the bike completely stripped down, and removed the rear shock and still can't get it off. Does anyone...

2013 FE350 I'm replacing a flywheel which was bent from a rock puncturing my ignition cover. Any hints on removing the roller freewheel bearing pack that fits into the back of the flywheel. It's in there tight. It's super spendy on top of an already expensive repair. Thx!!

Im going to try again this weekend. I have a 2001 FE501 as far as i know it is standard I onlt picked it up earlier this year. I need to get the rear shock off for a rebuild (leaking oil down the 'shaft') A while back I poped the caps off the swing arm, Cracked the nut wound it off a few...

so i am needing to get my kick-start off and gear shifter to get the cover off. But i can not.i think that when the po stalled then engine and tried to restart it, something happened to the kick-start. it got all chewed up. anyone have any help for me? I dont want to break anything. here is some...

Pretty good chance this has been brought up already.. The search engine failed to get me anywhere. I have the Forks off the bike, And the Tubes unscrewed from the Cap... The Nut that's held (inside the springs) is exposed. I understand that I need some kind of Pin wrench. I recall some one...

I saw a topic few months back about this issue but cant find it now. How can i remove the tank from my 09 Berg without destroying anything,and yes the bike has a cooling fan? I did it last week and used a lot of ''Man power'' but is not happy with that :oops:

hi all im removing all my electric starter....all the gears in the engine and the starter motor as it has not been wired for years so was wondering if any one new were in the uk i could get a bung that fills the hole were the starter motor was and how much they cost

Is it possible to remove the spark plug from an '04 FE650 without removing the Clark tank? The plug wrench will fit, but I don't see how to put a handle on it to break it loose or tighten it. Is there a trick or do you remove the tank? Thanks.

Hi guys, I've managed to fix the leaking water from the water pump weep hole, so that's good news... However, in the process I must have knocked the kick start shaft, as it is now jammed solid :angry: I want to have a go fixing this myself but understand I need to remove the clutch basket...

I've started to take my clutch side case off to install the Orangeberg weep hole kit and have been stymied by a very hard to remove kickstarter, I've tried heat etc, etc,! I'm in the process of modding a puller up to fit, hoping that works. Anyone have any tips, this should be very straight...

I am trying to change fork oil wt. but cannot see how to remove the cap from the cartridge to remove the spring. Fork legs are off the bike. The caps have adjustable preload (pin spanner holes). This is on an 05 FS650E. Any help is appreciated. Donald

Who has removed there catalytic converter from there bikes. If you have, do you need to have the bike remapped etc. Thanks

Guys, where is the connector that allows the removal of the rear indicators and number plate light? It looks like it terminates somewhere under the CDI box, but before i go pulling that out, does anybody know exactly where the connector is? Photos would be even better!!!!