remove

Whats the easiest way to remove the beringer front brake mount on a 07'650 to transfer to a 08' 550 tube w/brembo mount ? Are the tubes the same ? (I hope !) Think I might just buy the forks, tripple tree & rear shock off this other bike. Dunno if same or not... Thanks in advance---Proflow

Hi guys, I would need your help!! How could I remove the oil filter cover? I have removed both bolts marked as (1) in the image below, but what about the number (2), the center hole in the cover?? Please, help.... Best regards.

hello! The oil screen on my husaberg fe 400 2000 is impossible to pull out. Any ideas? I dont want to split the cases again. another question, is there any possibility that coolant is leaking from inbetween cylinder and cases? are there any coolant circulating below the cylinder? or is the...

Ok this is probably a stupid question, but how do I remove my front forks from my 2010 FE 450? Thanks!

Hi guys. Does anyone know how to remove the battery on FS650? it looks like I need to remove the gas tank or som other parts. in my instruction manual it only says to remove it, not how. :C

I removed lockwasher and nut and the hub does not just come right off like implied in manual. how do I remove clutch hub and basket without breaking anything? any advise would be appreciated Sorry it is a 2006 fe 650

[attachment=0:32kch7dd]1374671717148.jpg[/attachment:32kch7dd] ive got bearing pullers internal/external ive tried heat,ive even put a washer in between the bearing and casing to get a edge to hit it with a flat head screwdriver and heat just to get the pullers in but no dice anybody have any...

Hey all! I'm kinda new to Husaberg but having some maintence on my bike now. Going to change the rocker arm bearings, but cant get the cap ends/shaft out of the cylinder head cover. So, how do I do it? Tried to search for a forum thread about it, but couldnt find anything.. :( Andreas

I Have my new 2011 berg FS570 EU from Taiwan and I am swapping the OEM exhaust for a FMF. But I don't know how to remove the stock midpipe. Somebody can help me about the step or any picture. Thanks alot

Hey guys, I just signed up since I purchased a closeout deal on a 2010 FE 450. Great bike, but I am having fuel boiling issues also. I had the 70 degree subtanked installed by the dealer. I personally pulled the tank afterwards and put heat reflective tape on the underside of the tank. Now, I...

I think this is a gauze oil filter ? It won't budge. Should it just pull out ?

I Have my new 2011 berg 390 EU from Austria and I am swapping the OEM header for a FMF megabomb.. This new megabomb does not have the option for putting the lambda sensor, I installed my new header and turned the bike on and now the FI is giving me an error code with 4 long flashes and 5 short...

on road now and no need for any restriction, also like to re pack it if possible. how does this thing come apart? thanks in advance!

I have read a number of places and heard from a few sources that the oxygen sensor in the header pipe is not used for any purpose in the USA '09 model year FE 570 bikes. Can it just be removed and replaced with a flush plug? Or does it actually serve a purpose? If not, why is it there? Getting...

Hey all - I need to remove the gas tank to run some wiring from the new X2 HID to teh battery, and can't figure out how to remove the fuel tank. I probably could have finagled my way through it but it was time to come in for dinner, so I thought I'd just let somebody who's done it clue me in...

hi, does anyone know how i could remove the small, small bearings that sits in the engine and the clutch housing and holds the starter clutch

Hi, do i need the decomp stop nut even if i have a new decomp that doesn't use that one i was thinking of the balance

Which way does the bolt turn?? It is really on there tight. Not surprising, but after turning it a bit it is still very tight. When I encounter this I always wonder whether I am loosening it or tightening it. I know that some drive nut/bolts on various mechanical machinery has left handed...

Admin, please remove this post. Thanks

So I got a cam chain, and valve rocker arms, and a local engine guy is doing the work. He's very experienced with ktm, but not so with husaberg. Apparently on some ktm's it's necessary to remove the head to replace the cam chain. Is that so on the berg? Anyone got a link to a quick outline of...