protection

Hello, So, on my very cheap Craigslist berg the stator is out (It's a 2001 FS400). I get infinite resistance on the red and black wires. I would get mine rewound by Sparks or someone, but I don't want to sink too much money into this bike since I have no info on the history behind it and...

just thought I'd let you klnow that I am having the swing arm polyurethyne protector around the front produced for both the very old and just the old Husabergs! 12005201 which was available from 1989-2000 (all models) 12005203 which has just gone out of production was 2001-2003 (all...

Hi guys! I'm a proud owner of a Husaberg FS570, i only have one issue. When driving my shoes and pants get in contact with the exhaust, aaaand its kinda hot.. Ill attach a picture with what I need. I suspect that the previous owner removed this.. Where can i get this, the carbon protector...

New FE 570 and was installing a set of Seal Savers as I had great success with them on my KTM. When sliding down the plastic fork protector I noticed how the plastic fork protector and the Seal Saver were rubbing - just a matter of time before the Seal Saver wuld be shredded and interfer with...

This is a problem to everybody, as to ride through waterm it will get rusty in little time. There are some sprays to 2-strokes I know that they can spray on and it keeps it protected from rust. Does anybody know any spray which could help protect the exhaust?

Hi, As the title says, what's everyone been using to protect there Clutch and Ignition covers? I've started to develop some boot rub and would like to know what everyone else has been using to prevent this? I can't seem to find anything on ebay specifically made for the Husabergs, has anyone...

As a new owner of a '11 FE570, I have been looking for a skidplate, handguards and rad guards. Planning a trip to Moab in the spring and want to have all the bases covered. Could someone point me in the right direction to purchase these items. The rad guards must work with the fan as I will be...

After almost 90h on the bike i notice that the tank is beginning to get thin at the redmarked area :shock: ,i have also worn throught the sidepanel (marked red). Is there any good protection for it?? or any other ideas..i dont like the idea to have a hole in the tank.

Hallo, This is a very cheap engine protection. Its fits like a glove on the bike. For sale in the IKEA shop: BOHOLMEN Dish drainer article number: 101.452.86 Regards Husa-Belg

I have confirmed that the screws that are intended to hold the chain slider protection on the swinging are are m6 on the 08 models, however, some come with M5 screws? Does anyone know when the screws changed and whether the m6 is better than the m5 and cups that secure the protection strip?

What glue should i use to fix the filter protection which sits beneath the tank on both sides of the airbox. (Partnumber 800.06.096.000) With the old ones i could easely remove the old glue, so i prefer this type of glue. Any suggestions?

All, this might seem like a bit of a lame question, but not having seen any up close properly, do you know how & what exhaust protection bands are made from?? Are they some sort of hose with a spring/jubilee clip/tie rap etc inside?? Anyone got instructions to put one together? :roll: Cheers...

http://www.husaberg.org/uploads/Husby/ Joe, This is the description about the protection solenoids for use between the stator and the CDI, I hope this will be helpfull. António

just wondering what the best protection is across that radiator? not worried about the beauty of it-just protection and letting air get through! was told years ago that the exit was as important as the entry and that the entry should be smaller not larger than the CSA of the rad. :shock...

Hi, Any ideas about which material to use as air filter protection? I will replace the material sticked to the frame and fitted under the seat.