primary

The primary gear for the 2001-2008 models is no longer available. I have the possibility to manufacture these to the factory specifications on dimensions, tolerances, material and hardening. If there is a enough interest I'll have a batch of 10 pieces made. They will cost 1500 SEK ex shipping...

Hi good folks, just purchased a 2010 390 and joined the forum. Thanks in advance for your help and wisdom. I discovered a concern when coasting down my hill today. To reproduce the issue and for troubleshooting purposes, I coasted with the engine off, clutch in, and in gear, I'm getting a...

I have to replace the countershaft and see there is a puller needed to remove the Primary Gear. I am going to turn one up and wanted to ask if anyone knows what the thread is......I have read somewhere they thought it was 40 x 1.5mm but were not sure Thanks Lance

Dear All, In 2007 I bought a brand new Husaberg FS650E (2007 model) and from then I just loved it. For the first time since then I have a problem with mi bike. The Primary Gear 29-T broke. It is located on the crankshaft. The part number is 80032000029 and in the manual it is shown as figure...

Primary and secondary responses as they relate to T cells were discussed earlier. This section will look at these responses with B cells and antibody production. Because antibodies are easily obtained from blood samples, they are easy to follow and graph. BIO X4 As you will see from the figure...

hello again! I'm in need of a new clutch basket and primary gear. I have found these on ebay wich is supposed to fit. However my primary drive does not have a keyway slot. And the clutch basket on ebay has a needle bearing while mine have a bronze bushing. will this be a problem...

what is the spindle nut size for the primary nut (front sprocket)? 07 Berg 550 FE

Hadn't ridden my FS650C for several months and after setting the valves yesterday and starting the motor, I heard a rattle that I had never heard before ( did not have my helmet on at that time and could hear better) . Definitely in the clutch / primary area. When I snick it into gear and begin...

Hi! My engine make loud noise. I open left side and primary gear nut open by fingers, there´s also crack on primary gear. I need your help what else I should do or check. And what cost new primary gear?

My 06 450 fe started to make a rather loud noise in the engine and I shut her down right away and went home. Found the water pump impeller had 2 vanes missing as well as the clip to hold it. After removing the impeller I started the engine and it still had the loud engine rattle. Checked the...

[IM G]http://i47.photobucket.com/albums/f167/Sid100/HPIM1166.jpg[/IMG] what would cause this to break in half just as the pics shows ....now will i have to retime the motor .ie tdc and line the marks on each gear or does the 1 mark on the cam gear...

Hi Gang, I've had a good look and can't find the answer, DOC or elsewhere, so can someone help? I note that Dale suggests green loctite for securing the primary drive gear onto the crank end of later model Bergs. My question is, is this just the nut, of are we also loctiting the gear to...

Hi All, New guy here and I have to say that this site is awesome. One of the SMJ members pointed me this way and I'm glad he did. Here is my problem: Primary drive gear broke in half at the key link. Bike is at Longevity Racing (Husaberg dealer) getting repaired. When the primary went...

I am working through the final details of cutting in a keyed ignition and a buddy (who is electrically inclined) noted that he felt the yellow/red primary power feed for all the accessories was pretty small gauge - looks like 18-20ga. He felt it should be 16ga minimum - I tend to agree, but...

Folks, check out the pic. Has this happened to you? This was on a 550 FE 68hrs mild riding...

Without going into a lot of explanation we are building the prototype 03 450 engine as a 470.We are using a new crankshaft from an 02 fc470 complete with new piston kit and cylinder liner.There have been a few issues to overcome but they seem to be resolved at this point.One last problem is...