play

Just wondering here about end float? Just rebuilding a 628cc crank and about to check and adjust if need be the axial play. My other engines have always been around .75-.85mm without any adjustment and run perfectly. A quick measure of this engine ands its just over 1mm. What are the...

Hey husabergers, How much side to side play is allowed in the counterbalancer? Theres side to side play in mine, but not up and down. Heres a video of it: http://bit.ly/2sKTssw What do you think? Thanks in advance. Best regards, Christian.

loving my Berg, don't get out as much as I should though.. went to the last Watagans Trail Bike rally recently and for the first time noticed the play in the throttle.:confused: Its not much but the more I thought about it whilst riding the more it bothered me :mad::mad: I checked the...

Hi guys, Its been a while as ive been out on the bike ringing its neck everywhere :) oil change every 5 hours and nothing seems (touch wood) to be going wrong so pretty happy. Took off the cases to check axial play and for some reason im still getting nothing. I took the shim off...

Hi guys i rebuilt my bike about 15 hours ago and i decided to check crank axial play. i used to have ball bearing but now using ntn rollers. I cant seem to get any! not even the slightest bit of play?? the engine isnt tight and runs like a dream but i cant get play. im looking for circa...

What is considered normal play on the rocker arm bearings (axial) and axial play on the rocker arm itself when the shaft is in and installed on the head? My 570 today started to make some top end noise when idling. Heard it for the first time when I ran the motor pretty good and hot. It's like...

Hi, I was checking axial play of crank on flywheel side, by pulling it out and in. Can it be measured like what I do on picture? I measure 0,6 mm, like what I was reading in 'doc, that is ok for 2 roller bearings. Do you know what type of bearings were used in FE501 2003, in spare part is...

Hello dear, I measure axial play of rockers on my FE501 2003, and it's way out specified in workshop manual. Manual says 0,1-0,15, while mine have exhaust 0,25 and inlet 0,4. I contact Husaberg dealer who said that this is normal and that he newer change any bushings. Also there is a small play...

hi all i noticed a bit of excess side to side movement in the exhaust rocker when i was doing my valve adjustment i start by showing you the exhaust rocker then go on to show you the inlet movement and as you can see it is less. is this normal ??? thanks for your time dazza...

Have just finished reading a heap of posts I found using the search function, but they only made me more confused. :) Recently purchased an '04 built, '05 model FE450E. After a bit of reading here it seems there is a slight chance that the crank bearings let go. The bike has just done 40...

so this is probably a stupid question but i got to ask. I just got a 2007 husaberg fe550e. It's my first husaberg and i love it. now to my issue i thought i was hearing some chain noise like maybe it was too loose i checked it and the adjustment is right, but the front/counter sprocket seems to...

Hello all, I thought I would share with you today my new cool tool. It's a Snap on adjustable 3/8 crows foot wrench. It's got inch and mm settings for a maximum opening of 1 1/8. Good enough to adjust the steering head nut on our Husabergs which is 27 mm or 1 1/16. I just did a minor snug up...

Hi! I´m mounting the clutch now, and I noticed an axial play of 1mm, is that normal? Without the clutch mounted, the kickstarter works fine, but if I mount the clutch, I have no resistance 1/8 of one turn, and then solid stop. What have I done wrong? Can it be the resistance of all...

Is the trailtech DC stator kit a direct plug and play on an 08 husaberg?? there a long post on here about issues somebody had?? I want to buy the kit $169 for the 02-07 rfs bikes , just wondering if the instructions will work and the connections and wire colors are the same...

Hello Gentlemen Berg is still in pieces due to main bearing crash last september.Now i'm putting things back together and have some questions.. I am planning to install SKF NJ206 ACP /C3 HVC058 roller bearings,both sides+weld crank pin to halves.Pictures coming when it is done. Any...

Dr_C's gallry shows this, inner ends of the rocker arm axles are tied down by a pair of cover bolts. I cant't remember that here are any bolts there on my rocker cover. Thinking of it, it seems like a good idea to have them. What happens, without these bolts, if the axle inner ends start to...

Gazza posted a link to bike sales in Australia for the 1st Quarter of 2007 http://www.mcnews.com.au/NewsArchives/2007/sales_jan-apr/brands_overal.htm After looking at this I have a few a thoughts. Husaberg has very limited sales when compared to the top 6. Although the top 6 have roadbikes...

I just finished putting in new swing arm bearings / bushings, seals, etc in my 2006 because the bearings had spent too much time bathing in muddy water and had got in and done damage. After putting it back together I notice a little bit of play still exists. The bushings do not fit really...

I was thinking of maybe bringing a rim & tire to see if anyone would dare challenge boss in a tire change contest? must hold air? or something along those lines? Could be helpful in getting home, gas is spendy.How much buy in ect? Thought's?

I am in the process of rebuilding a KTM560 SMR that lost it's crank bearings after 6 hours.(brand new) I see that KTM and Husaberg both specify to only shim for proper clearance on the ignition side. Is there a reason to only shim that side? The reason I ask is when my crank was removed...