pin

Hello. FE470e 2002 A pin is broken, the one on the gear for driving the camchain. Should I just make a new one frome a pice of steel plate, is this okey?? or where can i get a new one? Will a DIY pin do the job.? 2nd: Problem two is a crack on the gear, see pics.. Should i replace this...

Hello fellow Berg`ers Does any of you know, where to get the female ECU connector (36 pin on wire harness) for a FX450, 2011? It is stamped, with very small letters "JST 36 UAA". Thank you in advance.

does anyone know where i can purchase just the sliding pin (not sure the right term) for the brembo front caliper? image attached so i can easily swap between 260 and 320 rotors?

Has anyone used a lighter than stock gudgeon pin? Standard pin about 65g Elko piston around 260g, Anything lighter out there pin wise? Many thanks

Hello husaberg forums, I accidentally dropped my water pump impeller pin into my water pump today and it fell all the way into my engine block. I tried using magnets and shaking the bike, it didnt fall out.. Any suggestions? Bike is a Husaberg FS650e from 2006.

I'm replacing my read pads and disc, And my 2007 FE Berg has the Brembo Brakes. I'm removed the cotter/split pin, But the "bolt" holding it in doesn't seem to want to come out.... Any ideas?

I have a 93 fe501. Im doing a top end due to a blown head gasket. While im in there Im taking a good look at the condition of all parts. I have .005 in/.13mm clareance on the wrist pin. seems loose to me. As I do not have a table of limits for this engine what is the factory spec for this...

I need the weight of the OEM pin and rod on the 628 if anyone has one to hand please? Taffy

Found this small steel pin and o-ring among some other odds and ends that came with the bike. Anyone recognize this? From a lever assembly maybe? [attachment=0:2x0j7gov]powerup-pin500.jpg[/attachment:2x0j7gov]

hi all just rebuilding my 2008 450 with the help of taff . thanks mate left on my own putting the water pump pin in i dropped the pin and it dissappeard in to the water jacket and pin is made from ss steel so magnet would get it out any ideas ?

Ok like the title says, any tips on pressing the crank pin out to replace the rod bearing? this is a 1997 fe600e. The bike is equipt with electric start and due to this there is the gear that meshes with the counter balancer in the way of the pin. The gear is pressed onto the crankshaft and it...

One of the caliper guide pins on the rear caliper is bent and is wearing the pads at an angle. I unscrewed it to try and straigten it out, but just mangled the threads. I searched bikebandit.com but the schematic doesnt show the pin as a single unit. It shows it as part of the caliper as a...

anyone had cause to break apart a pre-load cap? I need to dismantle the last part of this pre-load cap and I'm left with rebound pin looking at me. I can see two slots down the side at 180 degrees apart. regards Taffy

If this is in the wrong spot I apologize. I could not find a classified section. LH mirror mt needed for an 05 FS 650E. New, used or ugly OK jut functional. In the book it is called a CLAMP MIRROR WITH PIN, PN 590.02.044.000. It clamps the clutch, decomp levers and reservior to the bar...

Hi, In an effort to fit 100mm piston in the place of 92 mm,I had the reconditioner made a bush for bigger 20mm pin but when I got back to him to got the new stuff I realized he had made it out of brass instead of bronze.I am not happy with that.what do you think about brass piston pin bush?

05 FS 450C Bike has been making some louder than normal noise, so I check the valves. Little tight, I adjust and fine. try the bike and it is still loud. check to see if the main nut backed off and water pump pin was broken in 3 pieces. slight damage to the propeller. What could have...

just about to try and convert a 82mm stroke crank to 35mm big end pin. i would love to have had the most hollowed out pin ya can get. anyone anyone they can trust to guide me with info on that? regards Taffy

to remove the fork caps, a pin spanner is required. Does anyone know if there is a standard took, best way to make one, or does everyone buy the wp pin spanner?

ok a few months ago i had a problem when an engine i had buildt went wrong, i have mentioned it before and those of you that know me know that i'm relentless in my search to try and cure the factory's mistakes. essentially, this '02 650 crank twisted just tootling along running it in...

Gentlemen, Trying to put together a strong bottom end for roadracing. I have a 2005 FS650C with under 300 miles on it, including 90 miles on a 3 mile road course. The quick version to my troubles is the inner oil filter cap o-ring sheared when the previous owner installed it. A 3/4" (1.8cm)...