phm

I have bought myself a non running 2002 Husaberg FS650 I want to get running. Since it has been sitting for approx. 6 years I thought that I would clean the carb as one of the things. (It has a spark when kicking) I have taken the carb out of the bike and it is a Dellorto PHM 40 ZS...

Hi! i just finished the engine rebuild, when i start the bike the engine runs fine with choke on, as soon i choke off it dies. I cleaned carefully the carb, the idle jet is 42, the main jet 190, the needle clip is set at the leanest setting, is this correct? This problem came out after...

The engine start easily.have idling.i give gas when the cracking the exhaust and drowning.the valve clearence is good ignition good but i need the carburator full description.thanks!

just spent 5 hrs retrofitting a new PHM 40 that i got off of fleebay onto my 96 FC 600. I hope its jetted close? What pain in the @ss!! Had modify cable, make an adapter to air box, and mount external choke. now i see why it came with the flat-side dellorto. the PHM is a little longer about a...

Picked up a tagged KSO FE 400 and it was puking gas like the float is stuck/leaking. The problem seems to be a worn needle valve (worn rubber tip) so I'm going to do a total rebuild replacing all the brass parts. The CD1 Type Idle emulsion tube was missing so that will be added and I'll drop the...

Hi there everyone, I've got a Dellorto PHMzs carb that I'm rebuilding and I need some help with what jets to start with for my area. Elevation: 1,500 ft Temp range: 75-90 Bike: 2001 470 with Lineaweaver X2(IIRC) cam and Big Gun slip on (it's the bike that the wonderful members of the UHE gave...

Hi All, I`ve a FE400 with a Dellorto PHM 38 carb if i was to change to a 40 carb would it make any difference and what differnce would it make :?: :?: Cheers Bob.

Trying to set the float level on my Dellorto, from what I have read the metal should be parallel to the gasket surface.Is this when the needle is seated? What is the tab you see in the picture with the red arrow is this suppose to be making contact with the needle? This is how I found the tab...

Hello, I found on this forum many info about dellorto carburators. Because there aren't many fora where people have knowledge about dellorto carbs, Ill give it a try here. I have a KTM LC4 600(`94) with a 625cc cilinder(2001) on it but I have a hard time to jet it right I've got these...

Hi all, I know I am not talking Husaberg but I believe the KTM and Husaberg share some similar tech and so far I have not gotten any decent info from anywhere else regarding the Dellorto. I have a 97 KTM620 super comp. It comes stock with the Dellorto PHM 40 and the following jets: Main...

I ordered floats for my FE600E 3 months ago Husaberg part #ph25016801 and they are on back order until who know when. Dellortos part # is 15760.3 float single 4g. Any idea where I can track this part down. I would greatly appreciate it. Tom

I have the stock carb on the bike and have cleaned and cleaned it . I have a 185 main and 45 pilot , k51 needle . How many turns out should the mixture screw be and the idle screw. I noticed the needle had some corosion on it near thhe top and cleaned it wich showed some pitting near the top of...

Well I just stripped my carb to see what's there. I have :- Main jet - 185 Needle jet - 270DR Needle - K51 Needle clip - 2 Pilot jet - 35 Throttle slide - 4mm Choke jet - 45 mixture screw - 1 turn out #9980 idle emulsion tube is missing !! The bike runs pretty good but i do have...

Gent's Real broadly speaking ... I'm finding that after riding through a lot of water, i loose my tickover. So i screw the idle adjustment screw in a bit, but then it struggles to start off the button and generally requires fiddling with the mixture screw..... However, if it were dry, the...

I found a guy that is selling Dellorto PHM 41's. My 98 Husaberg FE501e has a PHM 40. Would this 41 work? Would it be better? Would it physically mount in position? My current phm 40 is worn on the body where the slide goes. I think it would be best to replace it. thanks in advance,