mounting

Hey team I went good hard forest riding in the weekend to see how the girl would go,well pretty interesting, first of all the gearing was in the stratosphere so I dropped to a 12th front sprocket with a 51 on my spare ktm wheel,18 inch but also thinking of going back to the 52,but man did she...

Hello Gents, looking for some insight into the mounting of my 600 engine. My swing arm pivot bolt is to large and there is some kind of brass fitting in the mounting hole. Is this fitting removable or interchangeable for another size ? Sorry can’t figure out how to upload my pics. Here is...

I got lucky to score a used but decent shape side stand for my FE550. Picked up both springs, bolt, rubber band and C-shaped hook. Can someone please post a pic how it should be installed? Thanks! Christian

I replaced the SEM combo cdi/coil with one from RegulatorRectifier.com. The coil and the CDI are separate. It works great and starts easier. I am looking for the best place to mount the coil. I am tempted to place it within the frame backbone. Has anyone done this before? fluidray 2003 FE400e

Just wondering where you guys mount your GoPro's when your riding, how it holds up off road with security and quality etc... I have the chest mount but off road I only really get my fuel tank as spend a fair time standing up. With it on the handle bar it bounces around and vibrates a fair...

Hi guys, I've just picked up an Auxiliary tank for my husaberg 2005 (fits 04' to 08' I guess), and the guy that sold me the tank has included the mounting instructions (Thanks R.!!!). When looking for the tank, I was unable to find the original instructions to mount it, so if this can help, I...

What is the best way to mount the timing chain on 04-08 models? The workshop manual has a procedure but it is with the clutch basket removed. I would like to leave clutch in. The head has been removed and reinstalled. I can get everything to line up O.K., TDC, balancer to primary...

Hi All- I assume the CDI mounting tab needs to be cut off? Can anybody give me more info on where the CDI is best relocated to? Thanks! Matthew

I bought this six piston caliper two seasons ago. When I bought it, I failed tp realize that I needed a different fork setup. So I ended up replacing the Husa FS forks for a set of dirt forks from a 08 KTM SXf450. Now the brakes bolt up and work VERY well. Only I ended upgoing the whole last...

Ok, Just got the new plate! :cheers: ... but immediately noticed I don't get any mounting hardware. The holes on the plate don't line up with the holes on the mud flap. Anyway...what do you guys do? Mount sideways? Drill the plate to match the mud flap? make something from some old tire...

Was going to order a Scott's under bar mount for new scoot, but found out after reading that FX has narrower spacing on bolt pattern that is on top triple clamp. Can anyone confirm this? The guys at Scott's dampners still show that the FX's are 90 mm spacing, and I think they are narrower... any...

All, When I bought my new 09 570 I mounted a set of hardparts radiator guards for obvious reasons. I followed the instructions given in the package, and the only obvious thing that I had to do was trim the top right side of the guard to clear the cable guide. It wasn't until after...

Greetings all, I just finished pulling off and putting back on the tank and upper sub frame truss on my 09 570. This to adjust throttle cables and check nuts and bolts etc... The center bolts go into an Aluminum tube that is embedded into the top of the gas tank. When I was torquing...

Hi all, I'm looking to purchase a Scotts(Ohlins) steering damper and was wanting to know opinions on what people think is the best mounting setup and why. It's for a FE550e '05 bush/forest riding only. I have another brand (MSC) currently above bar mounted. ie) Above bar...

I remember reading someone's trick for mounting the 5inch rear wheel, but I can't find it now. I think it was bringing it in from the bottom and taking the chain guide off.... Cheers and thanks Mark