lower

Whats the easiest way to remove the beringer front brake mount on a 07'650 to transfer to a 08' 550 tube w/brembo mount ? Are the tubes the same ? (I hope !) Think I might just buy the forks, tripple tree & rear shock off this other bike. Dunno if same or not... Thanks in advance---Proflow

Hi, Took the 2 x covers off the lower joint/bearing. Bearing itself looks and feels good (no radial, lateral, or longitudinal play). But I damaged the two covers in the removal. Don't need the whole bearing replaced - just those two cover rings. Looked high and low, and can't find those...

could anyone please let me know part numbers for 2006 550 lower shock bearings?also chasing a new bump stop,where would i find one? the old one is a mess.cheers

Hello husabergers, I have recently gotten my triple clamp powdercoated, and i am now having issues installing that damn steering stem again! It was a mess to remove, i used heat and a hammer and some hard knocks. My triple clamp is the adjustable one with either 16 or 22mm offset, but it...

Hi guys. I am new to off-road bikes and just bought 2010 FE390. My main problem is that I am pretty much vertically challenged at only 5'6". The bike's seat is 37.5". I did a bunch of searching and reading and found the following: X-bushing from Synergy seals (X-Bushing with Z-Bolt kit) and...

Crashed my bike into a bridge on the weekend and broke upper triple clamp and bent centre rod and front brake rotor.. If anyone knows of a place where I can source these parts used off a wrecked bike for chep that would be great! I live on Vancouver Island but have a friend in California whom I...

need to lower my 2014 fe 350, I've lowered the seat and would like another 2 inches,,,need direction,,, webfoot

hello! I basically put the lower cam chain sprocket the wrong way around and it slid all the way to the bottom with one or to gentle taps, preheated to 200C. There is maybe 2 mm room between the teets and aluminium. No chance for the puller to reach in. I did get some steel wire around the...

new to enduro riding have a fe 350 2014, any experiences with lowering bike? max distance, aftermarket products, all input welcome webfoot

I'm 6"1 tall, and think about putting the pegs into a lower position - like Fastway pegs in low-boy position. What's the experience with these on the 70deg Bergs, how they handle then? Many thanks.

I am only 5ft 8 and am struggling with the seat height on my 1999 FE400E, is there any modifications I can make to lower the rear suspension as I know I can push the forks through.

Is there a bushing or a kit available to lower the rear suspension on a 2010 FE-450 ? Thought I saw a post about this somewhere. If I could lower my bike approx 1'' or so It would be great...... :cheers:

Im going to try again this weekend. I have a 2001 FE501 as far as i know it is standard I onlt picked it up earlier this year. I need to get the rear shock off for a rebuild (leaking oil down the 'shaft') A while back I poped the caps off the swing arm, Cracked the nut wound it off a few...

so, a month left in my riding season i fixed(actually failed to fix) an oil leak coming from the clutch side case just above the oil fill plug. I went to go order the new gasket and figured i couldn't wait while they had to order one into my country. Anyway, i used a gasket sealant for a temp...

Testing the waters here. I have a FE570 I bought about a month ago that I am looking to sell. I have added Excel Pro Series Wheels black rims/Gold Hubs. I have not completed the break in on it, have changed out the break in oil at 1.2 hours. The bike has not been ran past half throttle during...

Is it possible to use the first gear from a Wide-ratio gearbox 1997 - 2000 engine in my 2004 650 engine? Wide-ratio gearbox 1997 - 2000 engine first gear 13-34 stock 04 650 first gear is 14-33 Regards

Thought I struck a bargain on fleabay @ 92 bucks delivered. Prorider KTM does them even cheaper, found this out after purchasing the fleabay one :oops: Have a look here: http://www.prorider.com.au/advanced_sea ... nt&x=0&y=0

The title says it all, does anyone know were I can get these parts?

How much up and down movement should I have in my swingarm with the bike on a stand rear wheel off the ground. Is there a bushing in the swingare that goes bad?

Hi All, Finally got around to pull the front out of the Berg today, the damage is only to one folk leg slider of which I have one coming from the Uk. The thing is how does one remove the aluminum casting on the bottom of the slider the leg I have coming is coming with out the casting...