lock

Hello I`m reaasembling the engine but now I have a problem. I want to tighten the 27mm nut in the clutch hub to 120Nm. But I can't lock the gears, and the wheel is spinning. In the repair manual from 2004, it says to use clutch holder 800.29.003.000 (can't find it online) and also to...

I am busy dissasembling engine and used a 2005 workshop manual I found on this site now the first page I am already in problems... On the photo in pdf theer is a locking bolt that is not on the 08 engine look at the pics. Can someone show/tell me where it is on the 08?

Anyone know if the ODI Lock On grips made for KTM 4 Strokes will fit my 2010 FE450? I called ODI and they were not sure. I've read a review on my bike that had them on, but it did not specify which ones. I'd like to assume the KTM 4 Stroke model will fit but thought I'd get your input first...

The lock on my 2003 fe400 locks fallen in bits,can you ger replacements or am i lookinf for used?

Hi all, after asking, searching Everywhere, I've found the FINAL SOLUTION for the VAPOR LOCK ISSUE affecting many HUSBY lovers.... you need to check the gap of the pick-up of the start (accensione in Italian) if this pick-up gap is not well regulated the engine stops and has incredible...

Hi. Valve Shims needs to be changed, to some smaler ones. Where do i take out a screw, an insert the engine blocking screw ptn 0113080802 in the part manual. Sinse I need to take out the cam. Sorry for bad english. Regs Burud

I just got back from a two week ridding vacation in northern Calif. It was a hot 100 deg.+day every day.On my last ride after a 10min. hill climb I stopped at the top of a mountain to wait for my buddy.(3-4 min.)When he arrived we motored on but I only got 100ft. or so then brrrrrrr. Ran out of...

Hi! I'm gonna buy a disc-lock with alarm, and I have been thinking about Xena XX6 Anyone got this? I know they have XX14 and so on, but I want XX6 because of the low weight (450g) compared to the XX14's 950g. I will probably need to have this lock in my pocket while riding. What do...

How can I remove the steering stem lock on my '97? I am going to do some welding and repaint the frame anyway so a bit of butchery is not a problem.

Has anyone done this? I am curious because I forgot to do it before mounting the big tank. I spent several hours with a heat gun reshaping the front of the tank for more clearance. I wound up with 38 deg left and 36 deg right using a machinist's protractor. (0 degrees being straight ahead and...

So I just pulled up to my chiropractor's office to see an '05 FE650 sitting by the door! I started talking to the owner who said he just bought it used, and it was already plated. He said it would be nice to have an ignition key and I replied that at least it had a steering lock. He looked and...

I have a quick question. I went to adjust the clutch on my 98 FE400e and found that down where the cable ends at the engine case there is a spot where the threaded portion of the cable housing goes through a small hole. The cable then attaches to the clutch lever. On my bike there are two...

Can some one tell me how to remove and replace the steering lock barrel? I have a new lock assembly keyed to match the keyed ignition... Cheers Mark

Does any one know how to get a key for my 97 fe-400 steering lock.

Is it me? Or does everyone have trouble tensioning the rim locks on these rim? I broke 2 today? I was so careful with the second one and still broke it? I use MSC rubber ones with a metal inner(that you cant see). I have even cut a section out of an old tyre to see what the problem is? I...