location

Hi all! I'm struggling to find the compliance plate on my 09 FE450. Can somebody steer in the right direction please? Cheers! Brett

Hi All i bought a fe 650 dismantled a few years back and have slowly been putting it back together but i have came across a snag. I am not sure how the spring sits on the back of the break peddle, i never seen it assembled. I see there is a 2 mm spacer and a 5mm spacer with a washer on it...

I was hoping someone would be able to help me out with the measurement for where the tensioner sit in the head. Following the explosion of the top end I've finally got it welded up but lost the location of the bolt for the tensioner for a 2002 fe400 head. If someone could help me out with this...

Hi All. Not sure if this is the same throughout the world but in the UK a number plate must be displayed on the back of a bike like this. I think the size really spoils the aesthetics and look of the bike. A number of people I have seen have smaller and smaller plates which are likely...

Hi all, I just installed a Scotts damper on my 2012 FE390. I took a number of photos as I went just to make sure everything went back together the same way it came off, I'm an expert at forgetting how to put things back together. So after fighting with the forks and top triple clamp for about...

Can someone please take a picture of where the choke on a dellorto carb is fastened? It has just been hanging on side since day one - manual shows a picture but still can't figure it out???? Moto is a 2001 FX650e thanks!

Hello, I just bought, Husaberg FE650E 2004, but horn was not on the bike. I got the original horn but I don't know where to position it. So where is original position for horn on this bike? Thank you!

After rebuilding my fs650 the gear from fist in second was a bit sharp/rough/jittery/clunky not extreme but just enough to anoying also the shift under light load from 5 to 6 was the same. Pulled it apart to check all was ok and was sure there was a extra washer under the spring shart with small...

Looking to find best location for temp sensor (in hose type) for my fs650. I was thinking the short hose coming off cylinder to top of radiator. Any one put one on there bike before? Will post pic's of alloy dash set up with Vapor on it soon. Thanks Glenn

I have antifreeze leaking from the right side at the top of the head around the bleeder screw beside the spark plug? And on the left side also what looks to be a drain screw below the coolant intake line.Or maybe between the head gasket? I have started the bike twice since I have had it and it...

Welcome fellow Bergers and others. After all the votes and opinions were considered the location and dates for the 2008 Aus Force Ride are now confirmed and are as follows: Venue: Black Gold Cabins Wallerawang NSW Australia. http://blackgoldcabins.com.au/ Date: Friday 23rd May 2008...

Hi OzBergers, Cafey18 and I and one or two others are meeting up this weekend at the DSMRA AGM, that is Dual Sport Motorcycle Riders Association Annual General Meeting. http://www.dsmra.asn.au/ No doubt we will be discussing Husabergs and the 2008 ride. The venue this weekend is...

Hey guys I noticed when I pulled my rear wheel off for maintenance, that there were two ways I could put the keys on the axle ends back in. The way they were in had the narrow perch touching the adjuster bolts. This puts the axle toward the back of the slot (with a good chain). If I...

What lines should you run the forks on for the newer Bergs? What line do you run the 1st or the 2nd? Thanks

Hey guys I have the small aux tank under my seat but the brain surgeon that designed it put the breather pipe hole at the lowest point on the top. So if the bike sits in the sun and the fuel expands the fuel pisses out. Has anyone re positioned this breather or made any modifications so the tank...

the original thread is waaaay long and I'm on a slow assed dail up connection. :cry: just looking for the exact specifics of where, when, etc

I noticed the bar clamps are reversable on my berg.It is not much offset,unlike my KTM that had two mounting positions.The bars are in the rearward position,behind the centerline of the fork tubes. Where do these bergs like their bars?Will I notice any difference besides being a little less...