limiter

I’ve taken apart my torque limiter but don’t know where to put the shim, and how thick I should have the shim Any info please as I can’t get me my head round the posts I have read about it The cork like material washer inside looks like it will fall to bits if I try taking it out.

I wonder if anyone can give me the exact measure from top to top of the torque limiter in the picture below. It's a FE 650 2007 model Thanks a lot

Pretty much since I got my bike, I've been having a hard time starting it. Sometimes it'll turn over for a few seconds and that's enough to get it going, but mostly it just whines at me and does nothing to the engine. I'm fairly certain that it is the torque limiter, as I've watched a couple...

Before I start this thing up and go for a break in run on my fresh rebuild. I'd like to know what the rev limiter is set at, so I can try to avoid hitting it. I can't find a single mention of it in the manual, and can't find any info online about it either.

Hi all has any one ever fitted or do u no if the 600 fe has a relimiter it's just to stop me over revving it as there's no power gains in over Reving the four stroker

Hi! anyone knows how to lower husaberg FX450 rev limiter? Target rpm would be somewhere around 4000rpm. http://www.magnumtuning.com/en/detail/r ... er-cdi-box Something like that but I dont think that -20% is enough. If somebody has done some sort of DIY part I would be very intressed of how...

Hi. My 2005 fs 650e has been having problems starting with the e-start when the engine is cold. the stater just spins and when the engine is warm no problems starting. I removed and disasembled the torque limiter gear and I found 2 cup washers instead of one. should I remove one and install a...

im having trouble starting my fs570 and think it maybe the toque limiter. anyone have a step by step procedure for repairing it? thx in advance for any info, rm

Guys, i have booked my 09 570 for the torque limiter to get done, as i am having the problems with the hot start issue. When i described the sympthoms, the dealer knew straight away what i was talking about. Now my question is how long out of warranty has Husaberg Au been sorting this out for...

Has anyone had issues with 09 or later Torque Limiter . I have ruled out all other possible causes of my starter stalling and thus not starting my 450. I have removed the limiter and played with it a bit in the vise ,it seems to work but I dont know the limiting value so I cant test it properly...

My FE 650 starter was slipping. It came time to dig into the bike and get it fixed. I went straight for the Torque Limiter, planning to shim it. To my surprise the "disc spring" or "spring washer" had a section broken. Now the disc spring has like a piece of a pie cut out of it. This is...

I’ve got 2 torque limiters here one from my 03 650 and one from a box of spares from a blown 04. Now as I’ve been messing around with the sprag spring (shortening it) I mixed up the torque limiters, from what I’ve read on the site there’s no mention of there being different ones but mine differ...

Can it be done on the bike without removing the torque limiter by just taking the side cover off? Or would it be best while the cover is off to go ahead and pull the clutch and tighten the spring on the sprague clutch??? Thanks. Roland

Hi All, Removed the starter toque limiter today and fitted the one I recieved from Dan at Motoexotica and this has solved the slipping starter problem. I tested the toque of the original one I took only 5Nm hence the slipage, I did the same test with the new one and I could get 25 Nm before...

After rebuilding my 550 motor which included a new sprague clutch due to slipping, when the button was first pressed the same problem persisted so the finger now pointed at the torque limiter, this was about 4 months ago price then was about 60 quid so I thought hell to it I'll use the leg, but...

Does the Husaberg engine have any sort of rev limiter built into the ignition? I find I am winding the engine up a bit on trails when the next corner is close enough that it's not worth shifting into third.

can someone tell me if the 06 fe 650 has a rev limiter like the katos, mine just seems to keep on pulling no matter what revs , ive clocked it at 180klms ph, and it wanted to keep pulling but i chickend out, not bad for dead standard dirt squiirter, cheers dan :P

Went to visit my closest dealer (Promotopieces, Mascouche, QC) today to check the primary gear nut and balancer nut and fix my starting problem. When I met the owner of Promotopices last weekend and tried to start my 2004 650, he immediately suspected the torque limiter. When the motor was...

I had my first ride on my FE450e last weekend and overall was very pleased with how it went. I used the race as more of a practise to see how I would get on with a 4 stroke, having not ridden one since an '86 XR250 I had about 15 years ago. Does anyone know if these bikes have a rev limiter...