length

Hi All, Have a FE550 and want to replace the drive chain. I have a 16 front 40 rear, not sure if thats the right setup. Looks like i have a 112 chain length.? Can someone out there give me a clue? Thanks

Hi Folks! Im looking for a conrod mesurment C/C for a Husaberg FS-650E 2004 year modell. Is it 128 or 135 mm ? Thank you :)

Is the standard rod length on the 630 motor 131mm? Trying to make a comparison with the XT600 rod 3TB (135.5mm) fitted to my 660 motor. Many thanks

Hello, i just bought FC 501 +- 98year (still dont know about capacity of this engine, im looking for diffrences between 501/600ccm3) and here is a question: I have 82 link chain inside, so it's a 600cmm3? or 501 with chain from 600? (i tink its not possible to put 78 link inside. But i need...

In the process of buying a 2005 Fe650e, it was advertised as a 2004 Fe650e and then the owner stated it was a FS not Fe. Vin search shows it is a 2005 Fe650e. I plan to ride it off road, but it has been set up with supermoto wheels and aftermarked rear shock. The owner measured the front...

A while back, someone posted this thesis which I finally had a chance to read. It was very well done by a student who took an FE570 engine and optimized the intake. Page 67 shows the improvement of his tuned intake vs. stock and page 62 shows the effect of varying the lengths of the intake...

Anyone with a 570 fs can tell me the side stand length? Can't bring myself to pay £80 for a shorter side stand. So going chop mine down and make a adjustable one. Thanks.

Hi guys I've just bought a 2004 fe450 and love it but only problem I have is I'm 18st and need a rear spring to match my weight...ktech have told me I need a 63-250-100 but the manual states that my spring should be 260mm so was just wondering if any of you guys could help? Regards Ronnie

I have purchased a set of Factory connection springs for my 08 550FE and the springs are different length. stock ones came out at 484mm and the new set is one at 484mm and one at 476-477 mm. Should I be concerned or is that in tolerance? it seems a little excessive and is there a way to work...

I'm looking for the measurement of the brake hose that i will need for a LHRB on my 01 fe650? If someone has done this conversion, i would appreciate your input. I'm going right from the clutch m/c to the rear caliper. Thanks in advance K

Hi im needing a new chain for an FE501 2003 model. Ive counted the links to be 57 plates on the outside including 2 split links (YES 2!!) Ive never quite got to grips with how to count a chain so what length should it be running? It has a 48 rear and either a 15 or 16 front I have both and was...

How many teeth can I go up on the rear sprocket without having to go to a new chain? Rear wheel is almost as far back on the adjusters as it can go. Currently the bike has 15/42 on it. I'd like to gear it a little more to off road ( tighter stuff).

can anyone tell me please on the new (012) closed cartridge fork is the spring length 450 or 485mm?...thanks

Just an open and hazy question which is deeply technical.....so no replies then!!! many of you 650 owner's over the years will have suffered seizures, oval bores and poor piston life. yet the earlier 600 suffered none of this? I put it that the rod on the 650 has always been too short by at...

I got some 4.6 wt race tech springs to replace my standard springs on the 2008 berg. They are apparently the right springs for the bike. I notice that the race tech springs are 3cm longer than the standard WP springs. Has anyone else noticed this? This will clearly affect the preload.

Are there any ill effects to taping the entire length of an exhaust header? I live in the desert where it is dry most of the time. I live with the bike boiling gas on almost every ride. On my latest ride I had a dry leaf start fire. The leaf wasn't too bad. But had it blown out of the bike...

Hello, Because the Dellorto importer didn't had the choke jet #40 on their part list, I ordered one from the Husaberg dealer as a normal Husaberg part. This choke jet is shorter than the original, #45, and doesn't terminate at the bottom hole of the float bowl but ends about halfway. Which...

There is a "130" cast into the side of my connecting rod. What does this mean? I eyeballed the rod at 123mm C-C using a tape measure. In the doc under tuning it shows 123mm for the 03 550 which I believe is the same for the newer bikes.

I ordered a new intake valve to replace the slightly bent one for my 2002 FE400. The part number I tried to order was 200 224 01 which I got out of the parts manual. I was sent an updated part number 590 36 030 000. Both are 35mm valves and are identical except for the stem length. The newer...

i run a fe 650 04, i have purchased an 05 slipper block and i know that i have to take the end off the cam chain tensioner. does anybody know what length the tensioner should be after the modification . measurement taken with the rod fully extended...