installing

Hey ! So i got my autodecomp for my 02 by mail today :) My question is how hard is it to install it and can it be done without taking out the engine ? Ive worked on engines before so not a total noob but dont want to start tearing it apart and do something stupid. and iam guessing the...

I have installed a Tusk Lighting Kit on my 2008 Husaberg FE 570 and am trying to get the Polisport Headlight to work, but am unsure of how to wire this device. I want to try and get a South Dakota License plate for this bike so I have more freedom to ride around the Southwest. Has anyone...

On a 2013 TE 250 installing the right side cover prior to the clutch cover there are 2 moves by hand parts behind the power valve area. I can not find any pics or how to align these 2 parts so cover sits properly.

Installs in minutes https://youtu.be/r8lCGTltAm4

Hello husabergers, I have recently gotten my triple clamp powdercoated, and i am now having issues installing that damn steering stem again! It was a mess to remove, i used heat and a hammer and some hard knocks. My triple clamp is the adjustable one with either 16 or 22mm offset, but it...

I have new mains and 1 transmission bearing to install on my 380 project. I have a shop press to do this. Do I need to heat the cases if using a press? If so, is it ok to heat the cases with the other bearings in place. Thanks in advance K

While I am waiting to receive my parts for a head overhaul I was looking through the boxes and boxes of spare parts I had on this husa and found a fcr41. The carb seems to fit perfectly in the boot on the head, but it does not fit in the frame boot. The FCR is about 97mm with a 62mm inlet...

I've bough a 10 390 that is plated for the street, has the blinkies and lights but no horn. I need that to make it legal to the letter of the law and wanted to know it there is a connector already on the bike I can plug one into. Thanks, DK

I'm doing my regular maintenance on my 2005 fs650e. I have always installed the water pump seal with the spring on the inside. I have never had any leaking problems. I read somewhere that the spring on the seal should be facing the impeller. Just wondering how everybody else installes them...

I installed the Enduro Engineering Grip Heaters this weekend. It was a siple and sanitary instalation on my FE570S. First, the instalation of the grip heaters themselves is self explanatory, so I'm not going to write about that. The instalation of the wiring and mounting the switch is a little...

Hi everyone, just ordered a TI FMF 4.1 for my 2008 FE 450 and was just wondering if any special mapping.....etc needed to be done to the bike before riding? i've read a couple of posts where people have indicated to just slip on the new exhaust and let the bike run/idle for 15 minutes and it...

Like the title says, with summer fast approaching Western Australia, i was seriously considering fitting a fan to my 09 FE570. Is it worth fitting a new upgraded stator at the same time (would allow for some upgraded lights as well)? I have a rekluse fitted, so no bump starts for me, so a...

I got a tank from boss this week and while trying to install it found out that the right hand gas line is no where near the petcock. I also did used the factory shrouds to place the tank even though on clarke's web site they say it doesn't (http://www.clarkemfg.com/cart/index.php ... ucts_id=96)...

I was hoping I can get some help installing the dual sport kit. I have the headlamp/kill switch installed. I got to the horn and was hoping to get help. I'm going to use the previous kill switch to trigger the horn. the horn it self (K&S, bought from BOSS) comes with no wires. Can you tell me...

I am replacing the rings on my 600. After I took the top end off the lower oil ring got bent from cleaning. I can't believe how fragile the oil rings are. As I only have only done two stroke's before what is the procedure for installing the rings? Is it best to use a ring compressor...

I'm going to be installing a new Timing Chain on my 02 FE501 once I get the new one from Boss. Has anyone detailed the install within this forum. Like where the sprockets need to be lined up etc.

Hi there, Never raced before but now I signed up for next years Erzberg Rodeo in Austria (look it up on youtube). ----------- You have to live your dream at least once ----------- Although I don't pretend to even finish I want to minimize the possibility to have to leave the race because...

hi could any one tell me if there is any special way to put the stator back on as i am just a beginner lol many thanks guys Barry

I just received my fan kit for the big berg. The instructions shows some fan mounting screw inserts pushed through the radiator. I am assuming that they went between the fins. My radiator doesn't have any holes for the screw inserts. Do the newer radiators have them? Or am I suppose to push the...

I finally got around to putting Dale jetting kit in last night and it went reasonably well. After much mental debate I left the AP rod in and will try it that way first. My major difficulty was in getting the throttle cable cover back on with the carb mounted - you can't rotate the carb...