inside

Ok so yet again it seems that my 70deg tank is fixed (knock on wood!!!!). The trouble is that there is a lot of pressure buildup inside the tank. Very often fuel spits out every hole posible. Through the airhose for example.... Ok so I didn't conect the two air hoses (from the front and the...

FE450 2009 somehow breaths fuel inside the airbox. There is also little fuel in motor oil. Any idea where I should start working this problem? Its not a leakage for sure. Thanks for help!

Looking to shine any light on this issue, any one suffered similar? I imagine the issue could either be caused by bearing failure or crank spread? What's my chances of repairs?

Today I saw that "hole" in my valve cover. Last time it was not there. It looks like it has been eaten by a chain? But the cam chain is tight even without tensioner. Has anyone seen something like that?

Hey all, In my recent valve check i pulled the fuel line apart and see this: I was very surprised! This is the upgraded 20 micron filter I had the dealer install prior to delivery and thankfully they gave me the 2 extras that the kit comes with. I'll be swapping a new one in when the...

What type fuel line is everyone using inside the tank when replacing the fuel pump! Does anyone know of a source for some of the original black fuel line used from the factory! You have to buy the whole kit from the factory as they don't list the line as a separate item. The only line I have...

My 1st topic :!: Bought this pipe off our local forum last week: http://www.wilddog.za.net/forum/index.php?topic=95707.0 Googling the exhaust, it was evident that unlike a normal slip-on, the header pipe slides into the silencer, as opposed to the slip-on, slipping onto the header pipes...

Here is a picture. http://imageshack.us/photo/my-images/818/imag0111v.jpg/ Full of dirt inside, if i remove the carb tube and the tube that goes down to the engine Can i just flush it with water? Or Will i get water somewere else where i dont want it then. Bought the bike yesterday, only had...

This day wasn't my best husaberg day. The bike has about 190 hours on it and I have always changed oil and checked valves every 15 hours. I replaced the camchain and tensioner 10 hours ago. The previous owner did some major service 90 hours ago... Ok, enough with the background. I'm not...

Quick question: i stripped, because i'm an idiot--the magnetic oil drain bolt--probably becuase the bolt doesn't have a rubber seal/washer (i forget the name of it right now?) so i've been draining my oil through the main oil drain bolt that sits right next to the magnetic oil drain bolt. To...

here's a press photo of the internals of the new engine. (Well, ihope it works out fine with the upload) Cheers, Adriaan

Hello All, I am no mechanic but I am trying too learn!! A few months back I noticed my front steering stiffen up periodically. I attributed it to my setup( 17" Michelin pilot rear and 17" trials tire front) I know this seems like a strange setup but it worked perfect for my...

just stripped the 400 this evening. what did i find? well i found that there are bits of big end cage laying in the sidecover but that 99% of the engine is in good nik! the clutch pack has had it and has adgitated the back of the alloy pressure plate which is a sh.. i'll skim .005" off...

http://video.google.com/videoplay?docid=-5815350492893860613&hl=en

ihave an 01 650 i. i feel the std muffler is a bit restrictive,after pulling it apart and having a look at the internals .i,m thinking of ripping the guts out of my tailpipe/muffler and making it a straight through system,similar to the performance aftermarket jobs. this thing has a 35mm i.d...

I don't have easy access to the bike right now and want to order up some of those motion pro quick disconnects with the integral shutoff valves. Cheers Mark