height

After completely ignoring this setting I though I better get it set up. I've read it's 9mm. I watched a few YouTube videos and no one does it the same. I get the whole make the float plastic float just touch the float valve damper but not compress it. But what they don't get is where the...

Hi! Im new to the forum, tomorrow im going to look for an HUSABERG 650 FE 2009 supermotard. Does somebody know the seat height, or someone with the same height as me? im 5,7 feet (173cm) is it comfy? And any tips when im going to buy it? where i need to look? Thank you very much!

I am only 5ft 8 and am struggling with the seat height on my 1999 FE400E, is there any modifications I can make to lower the rear suspension as I know I can push the forks through.

Hi all, I just installed a Scotts damper on my 2012 FE390. I took a number of photos as I went just to make sure everything went back together the same way it came off, I'm an expert at forgetting how to put things back together. So after fighting with the forks and top triple clamp for about...

I've had my bike out for a couple of rides with mates now and it struck me how much they stand where I sit. It then occurred to me that the reason I sit is because I'm too bloody tall for my 650 and end up hunched to be able to use the bars. Issue: I have a Scotts steering damper on my bike. It...

07 FE450 I am having issues getting my bike running after fiddling w/ the carb. It starts on choke and I can even adjust the idle very low, but when I take the choke off I can barely get it to run. I can get it to start if I give it a few throttle twists before hitting the starter. It will...

Just wondering what fork oil height you guys are running. I just serviced my forks today and the fork oil height from the factory was 130mm The manual says between 100mm and 120mm. Trying to get an average on what most people are running.

Anyone know the height of the FE 390? I want to make sure that it would fit in the bed of my pickup, underneath my ladder rack. Thanks.

Howdy. Does anyone have the installed valve height for the 2001-2003 FE 400? I've checked the official literature from 2001 to 2005 including owners manuals, parts manuals and service manuals to no avail. Oh and "the Doc" specification is for valve spring installed height not valve...

Howdy. Does anyone have the installed valve height for the 2001-2003 FE 400? I've checked the official literature from 2001 to 2005 including owners manuals, parts manuals and service manuals to no avail. Oh and "the Doc" specification is for valve spring installed height not valve...

Hi All, This is an interesting one, if you check your float height on a FCR by the down load official manual it says the float must be parallel to the carb body, if you go to the Keihin carb site the float height is set at 9mm, they are not the same. If you go by the manual when the float...

Hello Most fairy tales start with once on a time.... For this forum probably more like I had lying on a shelf.... a Wössner piston part #8602DA with casting mark at the bottom W4108. I compared the pistons, too quickly yes, and installed the Wössner piston. The piston comes 0,3 mm above...

This Poll is to see what everyone is setting their fork height at. If different or other please explain. Pollo

Hi all! I have a short question: How large the optimal height of the autodeco? Thnx, oTo

400 piston (y2k - '03) i need the deck height? as it says, anyone swapped one out for another or gone up in CC etc etc? the height i need is from tthe top (or bottom) of the gudgeon (wrist) pin to the edge of the piston within 0.1mm? regards Taffy

g'day everyone, just wondering, is there a way u can adjust the seat heigh/overall height of a husaberg fe501 ????

Hi, I´m looking for the correct Throttle valve height Couldn´t find any info :( in the owner-,workshop- or parts-manual & owner doc ... Carb is a Keihin FCR 41 , Bike a FE550/07 Can anybody help?

can i ask for info on what is the accepted ride height for the rear? k-talk has had a heep of trouble catching up with the changes made to the rear shock and i'm not sure we're not involved too. my ride height for an '02 was 85-100mm. yet they recommend 100-115mm on k-talk. did...

Hi, I was looking at lowering the ride height slightly on my 501, but it's something I've never done before. I was just considering winding in the WP rear shock and raising the front forks slightly in the yolks/triple clamps. Would this have any serious effects on handling/stability...

Hello Again 1) I was just reviewing the data that I have so far on the Husaberg, whilst drawing up the liner and crank for the 750. I noted that Dale said that the Deck height with no gasket is 0, well on the 2003 650 that I have stripped the deck height is 2mm i.e. the piston is 2mm below...