gears

Hey guys I own a 1996 husaberg FE 600 and I’m missing a starter gear some where between the starter motor and the crank, is there anyone out there with an exploded diagram of the engine so I can see what gear I’m missing Thanx guys

Hi i have a problem to change gear to 2-> 3. The lever is so stiff i cant use leg, i have to use hand instead. Where should i look for the problem? Do i need to open whole motor? :eek: Ps. Sry for the bad English. Thanks for the answers! Kalle

Hi guys I have a 2002 fe 501 , I have just replaced the stator and a few other things to try and breathe new life back into the old girl. The question I’m asking is regarding the ( I think a timing mark) the bottom gear of the cam chain. Is it supposed to be in between the 2marks on the gear...

hello! I have some severe piting on the clutch outer basket and main gear/primary gear. I believe this is producing metal flakes in the oil screen. I have a husaberg fe 400 2000 will these fit? Husaberg 400FE 1996 400 FE 96 Clutch Basket | eBay according to the parts manual this...

Never had any use for the kickstart assembly as there's no room between the frame rails so while I've got the motor apart it's time to shed some weight!;)

Hi everyone, I'm after a bit of help please. I went out for ride the other day on my 650, the plastic swing arm chain protector broke and got stuck in the front cog, I pulled it out and tried pulling away and I had no first gear, second gears was jumping in and out but the rest were ok. Then...

Hi, I had problem with my bike. When I bought it after few rides, when I changed the engine oil I found a piece of gear tooth. It was tooth from primary gear. Wright now after 40mth I found next piece of tooth in oil. This time is from gear from balancer shaft. Why is it happened...

Sometimes when I shift I get stuck in between the gears as in being in a neutral gearing. What could cause this?

Hi guys, I'm having problems with my 20 hours old FE570. It has a Rekluse EXP 2.0 which was installed by the dealer in New Zealand. About an hour into my ride on Saturday the bike dissengaged out of gear, then I engaged it again and it dissengaged shortly after and refused to engage in any gear...

Any suggestions for front and rear sproket setup on a 2010 FX450. Most of my riding is on trails with rocky hill climbs. The factory sprokets are slightly too tall which means I have to take those rocky hills faster than i want otherwise risk stalling. Any insight would be appreciated.

hi! today i started my bike and went to ride but there was a problem, only gears 1-3 worked and it was hard to get 3rd gear on. Yesterday i noticed that gearlever was working kind of strange, it suddenly changed the gear and i wasnt doing anything. Atm, the lever is jamming and working very...

Hi, Due to cracked gears I need cheap second hand transmission gears for my engine.I am not sure if any KTM gears are interchangeable with my '03 FE400 but maybe I can change gears as pairs to match teeth if they are compatible with my main and counter shafts (I mean if the distance between the...

Ok, I was out on my 07 FE550 today and the above happened. I rode home drained oil and found a few bits of metal in the screen and a one intact roller bearing and a few bits mashed up stuck to the drain bolt. I don't have workshop manual to check which bearing has failed. Is this going to cost...

Ordering parts to do my top end refresh and wonder ....thoughts on skiping the cam gears when doing a new chain?? and is the 05 550 a 66 link did or something better?? Thanks bob

Im trying to find the source of a loud, high pitch whirring/squealing that seems to be coming from the clutch, its hard to describe but abit like a jet engine At best it is hardly noticeable (at tick-over) but at worst it is ear piercing. It seems to be worst at about 1/4 revs when coasting...

does anyone know why some bergs had only 4 gears , the cluster is the same as the 6 speed but missing two gears and one selector on the primary shaft . the gears can easily be added , i am just a bit confused as to why this was done :? regards scrap

Hello fellas, Does anyone know if gears from any model KTM can be used on my FC550? There no husaberg dealer in my country, but there is a KTM one. Thanks for any input! Vasko

Hi Please help, I put the bike on the right hand side to remove the cover and replace the water pump seal, finished up and now the kickstarter is jammed, won't move, I tried to bump start and when you engage a gear even with the clutch in it drags. it feels like it's got thick glue...

I HAVE A 2002 501 AND ITS REALLY HARD ON THE UPSHIFT REALLY BAD FROM 2-3 GEAR ANY IDEAS GUYS.

im refitting the starter back on a 650 fe before i start all the internals have been removed so have replaised the brocken slipper cogg and the roller bearing.now is there any more roller bearings that will have been removed with the gears from the starter system i cant see any in the owners...