early

I could use an early FE501 schematic to finish wiring my bike. The PO had removed most wires and kept a bare minimum like a MX bike. Meanwhile I have some questions: 1) on the 95's ignition module, there is one wire that is a mystery. The red one. Is that a power-on wire or is it a shut-down...

How many of you have a pre 1999 FC and a 1999-2003 FC Husaberg? I'm looking to find out the difference in the two stators? is it the same stator just spun around? I'm looking for a used early one and better still - a source for new ones? help! Taffy

can any one tell me is there any major differances between a 1996 and a 89/90

Has anyone had experience with putting 501 headers on a 350? (early model engine, mine 92) Did the power delivery broaden or shift? I purchased a later model 501 FC pipe to replace my FE long one and it included the headers, measuring ID/OD they are 15% larger. Would take a bit of heat +...

someone snapped this pic last thanksgiving weekend of my 2010 390. I liked so much my wife did this to it

Had a lovely day here in Sweden today, just being out in the wild contemplating on my own, went down to the garage started the berg after rebuild, little did I expect there to be an icetrack ready for next weekend, it is! Earliest time ever, wohoo :) Expect some film after that of the "new"...

I just noticed that my bike has the mx muffler (FC in husaberg notation) although it's an enduro model (FE). When looking at photos and old brochures the FE muffler extend all the way to the mud guard/rear light and seem to be about 150-200 mm longer than the FC muffler which stops right after...

Hi all We should, as BERGS lovers, put together all the info about the earlier bikes, so we don't have doubts about the year. I have doubts about the early ones 89 - 96, we should all try to find and scan brochures from this years, and official pictures, not aftermarket decals. After...

we have ordered just 10 con rods for the 1990-1995 350 and the 1996-2000 400. they are due at the end of next month-May. we have taken two pre-orders so 8 left. when i get these in it will mean that all tthree early engines are covered again for the first time since the factory...

Does anyone have info on the Husaberg yearly production figures before they were bought out by KTM?

I recently picked up a 1999 Husaberg FC600. It has the factory head pipes, but the previous owner fabricated his own muffler. Although he did quality work, the muffler is too short and the outlet is too large - it is way too loud, and just sounds bad. I picked up a Laser brand muffler off...

Does anyone know what early year berg whelks will fit my 01. 96 up to 99 wheels seem cheap and easy to find....will they work on mine?

New member in the US here, contemplating buying a 96 FE 400. Talked to the owner already who seems very knowledgeable and had the stator rewound in Spain and maintained things himself. I feel good about what he's told me, I too do all my own work and if it's something I've never done, I learn...

Pulled into my local shop to pick up my 2011 250 XCF that I race and having recently sold my 2010 FE450 I wanted something lighter for trail riding. Seeing I still have Husaberg pants, jerseys, gloves and jacket.....how could I say no?

I've been needing valve seals for my 98 501, and the suppliers I knew of were backordered. It's the only thing my bike has been needing, so I dug into it. My local KTM shop said that LC4 engines use VW Scirocco valve springs, so it got me wondering... I cross referenced the PN on my valve...

Hi everyone, i have search the site extensivly, even joined supermotojunkie in hope to find answer but none yet.... I am planning an extensive restoration of my 1997 fe600e this winter, currently saving and planning....as i drive on the road more and more i would like to get a set of supermoto...

Any recalls on early Dec 2008 sold dates , 2009 FE 450s ? Mine still pops ( backfires ) a few times . One time off a jump to ground ( BOOM ) then CRASH :evil: . Then the impeller bearing went out . weep hole was leaking . Bought bike used with 30 hrs , now has 45 hrs. Anything I...

Hello all, Just a tip when updating this part. When I splitted my engine I found the single bearing counter balancer and decided, according the Owner's Doc, to replace it with update part # 210 243-01. This part seems to be discontinued and I received part # 800.30.057.100, balancer model...

you all know how quiet the site can be after christmas but it seems the site has been pretty flat for a month now. i have decided to back off on my posts here as i am doing long hours but i'm sure that if there are any of you left that recall.....the site has slowed down significantly...

i have a '00 head here and the valves are tiny compared to later. looks like 32/27. anyone know what the valve sizes were in the 501/600? trust it would fit? what do we know about the std systems? i trust the 501/600 had bigger headers but all shared the rear section? regards Taffy