axle

2010 Fe450 Little help? Can anyone tell me what this is/does? Fig 40 on fiche? its a 10 or 12mm hex head bolt on the rotor side of the axle under the axle nut. When I tighten it seems to ratchet or click? I just finished replacing the brake pads and installed a new rotor and now the brakes seem...

I've bought lc4 supermoto wheels to convert my 450 , the back spindle fits like a gloove but the front needs work. I know that there are several names who produce reduction kits to fit 20mm axle in 26mm fork setup, but i'm keen to make my own. just need to know what parts go in that kit. Left...

Hi all, I have a WP Extreme fork from a Fe600 (might from 1998, not sure) that I will install on a Suzuki DR800 It came with wheel axle and 2 spacers on it, one steel and one aluminium, similiar thickness, same i.d. My axle is 17mm Now I need to buy front wheel and caliper/bracket as...

Hey, i ride a husaberg fe650 2003 taffmeister upgrade. I have a problem. When i ride a little bit the o-ring att the kick axle slides out and it becomes a oil leackage. Is this normal? Are maybe the o-ring to small or the kick axle has slide a little bit out? From the kickpedal to the o-ring...

hi my 650 supermoto 2004 model has a front axle with a castle nut on it can anyone tell me where i can either get a genuine type nut for this or an axle that takes the nut that threads into axle many thanks

Got myself a -04 fe650. :D After a quick test ride I noticed there's just a washer where there should be a nut, the swingarm axle had snapped the end of it clean off. :eek: Can I fit older (-03, -02, -01) swingarm axle to my 04? From the parts manual it seems they differ from the -04..

Looking into OEM wheels from a 2005 650 for my studded tires. Wanted to know if these will fit my 570? Life is good!

Does anybody know the axle size for a 2011 FE 570s, thank you.

Hey lads, I've got some generic sliders I'm going to attempt to throw on the berg. http://i.imgur.com/MYfhxZC.jpg - This is the L/H side. http://i.imgur.com/UJsitIK.jpg - This is the R/H side. That cap comes off the screw. Do I need to drill a hole through that for the rod then put the...

Howdy: Looking to swap a set of forks into my bike, and wondering what the axle lug offset (distance between the center-line of the axle, and the center-line of the fork legs - as seen from the side) is on the later model closed cartridge Husabergs (with the 48/60 forks). I have searched all...

Last time I pushed the fork leg in a little to cover up the black, but that will add to stiction, right? Of course, like this, the wheel isn't centered between the fork legs, so that will apply some sideways force on compression, which will add to stiction.... How do you guys do it?

Hi looking for some help with front wheel spacing. When using the axle reduction (20-26mm) kit do I need the original wheel spacers? The kit comes with one spacer and I have ordered one original spacer as the wheels I bought hade none. So is the spacer that comes with the kit to replace the...

Hello,recently I bought some triple clamps with less offset,around 11mm.It was a sweet otion to buy them,because I was searching long time to found them.The pre-owner said that the yokes fits perfectly but when I tried to instal them,I found that fits to frame but they are 12mm wider from...

Have a 2011 570 and was out for a ride , was quite wet and muddy at times and as rough as bags also ,I felt like i was getting a flat through out the day, then heard a real bad crunching death noise and chain rattle , thought my gearbox had lost all its gears, pulled over, axle with nut and...

Anyone experience with replacing the kickstarter axle from a 2003 FC 550? Today i tried to start the FC/FE 550 of a mate and the kickstarter axle broke. Weird experience to encounter. Is it hard to do? Do you have to take the engine out of the frame? It's a strange bike. It has lights and was...

I've just sold my WR250, and I'm anxiously waiting two more weeks to pick up my new 2010 FE390. I was wondering if I should pass on my combination tire levers/axle wrenches to the new WR owner, or if they'll fit the 390. As I don't have my Berg home yet, I don't know what the axle nut sizes are...

Hi i have just got a axle reduction kit from KTM so some 02 Berg wheels will fit my 04 bike. So the front wheel has a spacer in it on the disc side but i also go a spacer with the kit, does this just replace that spacer and also do i need to remove the speedo arms that are on the other side of...

I want to know from where and what model of axle sliders can feet on my bike... i want for both wheels fron and rear..i prefer red!!!can i install from ktm??? thanks...

O.K., I've got what I hope is a stupid question for someone... I got a front axle pull handle with my '10 450, and I cant figure out how to install it on the axle! Am I supposed to drill out the hex end of the axle, and press the pull handle in? HELLLLP! :mrgreen:

Wondering of anyone has found replacement axles with a pull handle ? Also do the KTM parts for a similar year cross over ? Any suggestions ? The bike is an 06 FE. Thanks in advance... Darren