1994

94 FE 350 I need the rubber intake boot. Where the carb connects to the engine. Any help directing me where to look would be greatly appreciated. Thanks in advance.

94 FE 350 I need the rubber intake boot. Where the carb connects to the engine. Any help directing me where to look would be greatly appreciated. Thanks in advance.

Hi, I have to install my Speedometer. But there is not enough space between Speedometer, Brakeline and Lamp. Is there anywhere a Picture from original mounted Parts? Thank you very much. Achim. Speedometer is original with 24km on its counter. ;-)

Aside from the obvious body parts differences, are there other parts from a '94 FC600 that I can use on my 2000 FE600E? Engine parts, exhaust, carburetor etc.? Thanks guys.

If you have any interest in the bike let me know and I will send you pictures and info. From what I know it was imported in 94 too Canada, from what I understand the numbers were very low. The bike is complete and in strong running order. The case has never been split nor has the top end been...

1994 Sales Brochure, part 2 of 2

1994 Sales Brochure, part 1 of 2

I have a 1994 FE600 without battery, electric starter etc. There is one yellow wire from the stator which connects to the yellow wire on the regulator. The regulator is a small cube with just a yellow and a black (frame ground) wire. I get about 17 volts AC out of this without load. 1...

Hi all, I have a shed full of Husaberg parts that the wife needs out of the way. The plan was to put the bike together at some point, but time has never been in my side!! Happy to sell as a job lot or in parts separately. Way too much to list, but there is Ohlins rear shock, WP forks, 2...

Hey everyone, I finished up my rebuild on my 1994 501. The bike started up on the first or second kick and ran great in the 10 minutes I had it out. That's the good news. The bad news is that I found a clip laying on the table that I am about 95% sure that it is a piston circlip :cry: I'm...

Hello, I just started a rebuild on my 1994 Husaberg FC501. My cylinder is scored and out of round so I would like to bore it and buy an oversized piston. I read that it is possible to bore the cylinder and use a 551 cc later model piston. My question is: Do I have to resleeve my cylinder, or...

I picked up a 94 FE350 in the spring, and just got around to it today, try to make it run. So after a few kicks no success, found that the float valve was sticking, also need to replace the fuel lines and the fuel pump lines. Other than that just one thing. It needs a Carburetor Boot...

With no history on the bike except that it's a bit hard to start and with an upcoming tear down/status check I have the following questions: 1. I have read here that the cam follower bearings often go bad and should be replaced periodically. Is it enough to inspect them or should they be...

After taking my fuel tank off to clean it out and replace the lines, I have realized that hooking it up is more complicated than I thought. The tank had been disconnected before I bought it. I think I have an idea of how it should be hooked up, but without any prior experience working on bikes...

Hello everyone I am new to the Husaberg world. I have recently purchased a 1994 husaberg 501FE from an older gentleman. The bike needs a little TLC but over all is in good shape and started up and ran fine after the 2nd kick and 2 yrs of sitting in a storage unit. I was wondering if anyone could...

Hello recently picked up a 94 husaburg fe501 needs trans gears and a rebuild got the bike apart put it back together to make sure it was all there have a couple parts that I couldn't figure out where they went so I'm looking for a repair manual for the motor so I can figure out where these parts...

1989 to 1996 Husaberg FE 501 First Production Model Owners Manual 1989 Husaberg FE 501 Owners Manual 1990 Husaberg FE 501 Owners Manual 1991 Husaberg FE 501 Owners Manual 1992 Husaberg FE 501 Owners Manual 1993 Husaberg FE 501 Owners Manual 1994 Husaberg FE 501 Owners Manual 1995 Husaberg FE...

anyone where holds spares for this , i need a kickstart lever thanks

anyone have a wiring diagram relevant to anything from 1989-1998? thanks Taffy

I have my buddies 94 600 Fe? i think, and it needs an oil change, what oil wieght is best? does it use the same oil for the tranny? If not what oil is good for the trannsmission? Where is the drain plug? And also where is the drain plug for the radiator fluid? Thanks