quiz again!

Taffy said:

1. there are three dogs on the gears but what else can be said to be "three off" on the bike?

2. how many kitchen utensils (by name) could you find in the engine?

3. where can i find some friction welding on the bike?

4. where can you find a ball bearing all alone instead of a team?

5. if i go past 153 where am i?

6. can you find something that is "20" on the bike and how high up can you keep it going
i.e. one handlebar. two wheels etc etc

7. what stops the frame resting flat/flush on a paddock stand?

8. which bearing on the engine can be fitted from either direction and either way up?

9. what is swedish on the new model?

10. how many cams are there on a husaberg?

Click to expand...

Coastie said:

Ok I'll kick it off.

1. 3 cylinder o rings, 3 shift forks, 3 screws on oil pump cover, flywheel housing, SEM stator and wp housing.OK BUT SOMETHING MORE PROFOUND PLEASE
2. shift "forks" AHA THATS ONE THING
3. NFI
4. oil pressure relief valve, front fork adjusters CORRECT AND CORRECT AGAIN
5. NFI
6. 36 spokes, NFI on the "20"
7. chain roller CORRECT
8. cam bearings, NO counter balancer bearigs NO, the gearbox 1 in the centre of the left case (secondary shaft?) NO
9. the name NO
10. 2 - camshaft and gear selector cam YES

Click to expand...

DaleEO said:

1. Three hand controls; brake, clutch, manual decomp, three foot controls; brake shifter, and kickstarter, three rear shock adjusters; slow speed comp, high speed comp, and rebound. three windings on the stator; ignition, and two separate charging coils. three lobes on the cam; exhaust, intake, auto decompression, three shift forks, CORRECT BUT THERE IS SOMETHING ELSE VERY PROFOUND

2. shift forks, clutch plates,pressure plate, SO WE HAVE FORK AND PLATE SO FAR

3. brake pads to rotors, friction plates to steel plates, NO

4. oil pressure relief valve, accelerator pump check valve, stock headlight light switch, kick starter latch, suspension clickers, IT WAS IN THE ENGINE AND THE OIL PRESSURE RELIEF VALVE

5. 154 NO

6.

7.the diagonal frame rail under the engine. NO, THE CHAIN ROLLER

8.

9. Joakim Lungren, Bjorne Carrlson. HA! HA! CORRECT

10. the cam shaft, the automatic decompression lobe, manual decompression BAR, gear selector STAR, ALL CORRECT

Click to expand...

Taffy said:

. there are three dogs on the gears but what else can be said to be "three off" on the bike? THIS ITEM IS A PROFOUND PART OF THE BIKE, SO FORGET THE SMALL STUFF?

2. how many kitchen utensils (by name) could you find in the engine? WE'RE ON 2 SO FAR

3. where can i find some friction welding on the bike?

4. where can you find a ball bearing all alone instead of a team? SOLVED

5. if i go past 153 where am i?

6. can you find something that is "20" on the bike and how high up can you keep it going
i.e. one handlebar. two wheels etc etc NOT MUCH SO FAR

7. what stops the frame resting flat/flush on a paddock stand? SOLVED

8. which bearing on the engine can be fitted from either direction and either way up?

9. what is swedish on the new model? SOLVED

10. how many cams are there on a husaberg? SOLVED

Click to expand...

awilksch said:

I'll ave a go Taffy...
1. - Exhaust retaining springs or Number plates (plastics) NO
2. - Float 'Bowl' SUPERB! A WINNER
3. - (any model 650 in Australia up to 2006' main bearings..LOL) FUNNY MAN!
5. - Close of intake valves?? end of induction.NO
6. - Could be hose clamps - various sizes and types counting those on the cooling systen, crankcase breathers, carbie vents & overflow tubes and fuel lines and between the rear brake master cyl and reservoir.
8. - big end crankshaft bearing NO
EXTRA POINTS - 9. - the name - the rest is Austrian..LMAO. QUALITY!!!!

Cheers!

Azza.

Click to expand...

Mogly406 said:

3. Valves DA! DA! SPOT ON
8. Main shaft bearing in RH case SPOT ON

Click to expand...

Taffy said:

DaleEO said:

1. Three hand controls; brake, clutch, manual decomp, three foot controls; brake shifter, and kickstarter, three rear shock adjusters; slow speed comp, high speed comp, and rebound. three windings on the stator; ignition, and two separate charging coils. three lobes on the cam; exhaust, intake, auto decompression, three shift forks, CORRECT BUT THERE IS SOMETHING ELSE VERY PROFOUND

2. shift forks, clutch plates,pressure plate, SO WE HAVE FORK AND PLATE SO FAR

3. brake pads to rotors, friction plates to steel plates, NO

4. oil pressure relief valve, accelerator pump check valve, stock headlight light switch, kick starter latch, suspension clickers, IT WAS IN THE ENGINE AND THE OIL PRESSURE RELIEF VALVE

5. 154 NO

6.

7.the diagonal frame rail under the engine. NO, THE CHAIN ROLLER

8.

9. Joakim Lungren, Bjorne Carrlson. HA! HA! CORRECT

10. the cam shaft, the automatic decompression lobe, manual decompression BAR, gear selector STAR, ALL CORRECT

Click to expand...

Click to expand...

Taffy, can you explain what friction welding is??

Click to expand...

Taffy said:

it's the strongest form of welding known "apparently" (which i don't believe). you stick the stem of the valve in the lathe and the head in the post and run them against each other till they turn orange and weld together.

regards

Taffy

Click to expand...