Husaberg 06 fs650 will not start, backfires

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
M

Mater

Joined
Oct 15, 2016
Messages
4
Location
Finland
I just rebuild my bike and when I was test driving it, i didn't have time to pull the clutch in when a car in front of me braked, and the bike stalled. After that the bike has not started, not with kickstart nor e-start. It back fires some times, and the fueling is on point. I started to think if if the timing chain had jumped one tooth, but when at tdc the timing looks correct when inspecting from the clutch side from the two gears. Where could the problem be? Any suggestions?
s2Lw2
 
Last edited:
uhm ...I am not sure if my suggestion can be correct but check the valves ...It happen a similar situation on my pit bike, I was teaching my gf how to run it and she had one of those stupid fall and stall it, it did restart for one second and backfire...and wont start again...I open the engine and find out a valve dropped (engine blow)

but that's a 300 pound chinese engine I really hope it's not the same in your case
 
Valves and valve clearances are ok. I get a good spark, compression and fuel. Me and my friend got an idea that altough the spark is good when the plug is out maby it isn't strong enough under compression?
 
Could be ...but if you got spark, compression(with good timing and valve), and fuel then should start ...expecially if it was fine just before ...what I can say recheck carb but even try to change the spark for what it is might be worth replace it and see if that fix the issue

....I been thinking of this one during work, try to replace the spark and see if it fix the problem I personally only replaced the spark once on the sxv when one of the cylinder went off but never had this issue for years since I move on 4 stroke, but what you describe is actually a Common problem on 2 stoke that the spark can go or it gets week when restarting ... let me/forum know the resoult

As long as engine mechanic (valve.. chain ...etc) is in place ...carb and spark are the 2 other things
 
Last edited:
Sparkplug is new, I have tried a normal sparkplug and also iridium plug. I have inspected the carb for wear and cleaned it also. Everything is on point, but still nothing, this is so frustrating.
 
It's really could be one of those this situation where there is an issue and you have no idea where is coming, I would take the head out and check it, at the end of the day is strange that a bike that worked fine won't start again after a stall ...also after an engine rebuild maybe a peace could had gone bad...I would check the head (take it off) and look at the case if you can see anything suspicious.. that's all I can think off
 
good luck! sounds like time for some linear troubleshooting skillz.
 
You could pull your rotor on the crank and see if the key is sheared or missing. Or use a degree wheel to verify TDC That would cause your problem. The mass has energy and when the crank stops suddenly and the nut is loose it can shear the key or at least offset the timing too far advanced.
Good luck
Riksoto

Sent from my SM-G930V using Tapatalk
 
Riksoto said:
You could pull your rotor on the crank and see if the key is sheared or missing. Or use a degree wheel to verify TDC That would cause your problem. The mass has energy and when the crank stops suddenly and the nut is loose it can shear the key or at least offset the timing too far advanced.
Good luck
Riksoto

Sent from my SM-G930V using Tapatalk
Click to expand...
Check the magnets in the flywheel they may have slipped causing the spark to be out of time.

Sent from my SM-G930V using Tapatalk
 
Riksoto said:
You could pull your rotor on the crank and see if the key is sheared or missing. Or use a degree wheel to verify TDC That would cause your problem. The mass has energy and when the crank stops suddenly and the nut is loose it can shear the key or at least offset the timing too far advanced.
Good luck
Riksoto

Sent from my SM-G930V using Tapatalk
Click to expand...

Check this.
 

Attachments

  • IMG_20160826_090128-2.jpg
    IMG_20160826_090128-2.jpg
    66.7 KB
  • IMG_20160826_090108-2.jpg
    IMG_20160826_090108-2.jpg
    72.8 KB
Picture on the left is correct, picture on the right is the result of a sheared key.
 
simple cap.

Hello Mater. Say guys, stop scaring him! If the plug is indeed correct, it`s time for a new plug cap. That`s usually the whole problem in this case. Just re-screwing the old cap on the plug wire does it if lucky. But change it anyway, 10 years old, etc. Cut a couple of cm off the wire while at it to get good contact. Could be a dying coil, but haven`t seen that since my XT550 Yam, in heavy traffic, on the most dangerous bridge we got, of course. Good Luck,L
 
Riksoto said:
What did you find?

Sent from my SM-G930V using Tapatalk
Click to expand...

The key on the flywheel is intact, I haven't had time to give the bike a closer look, but I will be trying a new plug cap and also I will be cleaning my carb once again :spin: . A family friend that is some what a motorcycle and car specialist suggested that the needle on the carb could be worn and that could cause too much fuel to get into the cylinder. Wish me luck.
 

Similar threads

C
Balancer Shaft not moving past certain point. What next?
Replies
0
Views
207
Connecticut_FE550
C
Benjamin Walsh
For Sale 2004 Husaberg 650 supermoto
Replies
0
Views
8
Benjamin Walsh
Benjamin Walsh
W
2010 Fx450 crank no start after engine work
Replies
3
Views
485
waylon
W
F
FE570 low idle issue, outside of the usual suspects! (I think)
Replies
2
Views
430
AussieBlue
A
I
Dream come true, sort of...
2
Replies
26
Views
2K
ihminen
I

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top