2007 Husaberg FS650e water pump seal.

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Joined
Feb 22, 2018
Messages
9
Location
Sofia, Bulgaria
Hello Everyone,

I have a 2007 Husaberg FS650e and stumbled upon an issue that I am confused about. My berg started leaking a little bit of oil near a tiny hole where the water pump propeller is. I know there are two seals - one from the oil side and one from the water side.
When I opened the side there was a seal behind the ball bearing #63 from the below manual, however, I do not believe the seal is the one marked #65 as it seemed different to me.
1695130883233.png

Does anyone know if this is the seal that should lay behind the bearing or it is a different one? If it is a different one can anybody tell me which is the exact part?

Thanks y'all!
 
65 is not a shaft seal.But an o-ring that sits behind the big clutch cover (where the water jacket is).
You are most likely looking for the seal of 63,this is a special bearing (6201) with a seal.
It was sold as one part,so the seal isn´t available separately.
It´s also a misconception of yours that the seal behind the bearing is used for coolant purposes,as it´s sealing towards oil.
The small shaft seal 10x18x4 is sealing towards coolant and the bearing is sealing towards oil.
Hope that helps?
 
The bearing / seal is number 63 in the diagram but does not show the seal that is attached to the bearing. That part has been discontinued. Options would include:
Remove the bearing/seal, clean the gunk behind the seal and reinstall.
Purchase a new side cover which includes the bearing/seal ( I think)
Purchase a Taffmeisters replacement bearing that does not contain the seal. A hole must be drilled somewhere according to his website. Contact him for clarification.
100867 - *Replacement 0625062013 Water Pump Outer Bearing (unavailable) 2004-2008, Taffmeisters

100867 - *Replacement 0625062013 Water Pump Outer Bearing (unavailable) 2004-2008​

£9.17

Write Review
Water Pump Outer Bearing (Polyamide) NO LONGER AVAILABLE Suitable For All Models 2004-2008 see photos of modification on Taffmeisters Facebook page **This is a 6201 C3 bearing with a thicker seal to keep the grease in. We think you'll need to drill a vertical hole of 2.5mm. Drill bit 2.5x95mm long OEM NUMBERS; 06250620..
 
FYI When servicing the water pump there is also an o-ring that go's on the water pump shaft which is also known as the counterbalancer shaft in the parts diagram.
 
Thank you for the answers, guys. I will keep you updated with my findings and what I did to resolve it.
 
So I replaced the ball bearing with SKF 6201-2Z model, however, the oil leak was not fixed. Actually, it started leaking more than before.
If anybody has a detailed explanation on how I can fix this, I am open to suggestions.
Thank you!
 
So I replaced the ball bearing with SKF 6201-2Z model, however, the oil leak was not fixed. Actually, it started leaking more than before.
If anybody has a detailed explanation on how I can fix this, I am open to suggestions.
Thank you!
Check this.
Solution to your problem.

 
I have been able to install this part when it came and it finished the job. There is now no leakage.
Thank you all for the suggestions.
 
Qualcuno l'ha provato?
SKF ICOS-D1B01
Si presenta identico al ricambio originale non più disponibile
 

Attachments

  • IMG_20240308_211525.jpg
    IMG_20240308_211525.jpg
    22.4 KB
Last edited:

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top