New Berg Owner.. HERE ARE THE PICS!!

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
T

tawheed

Joined
Jun 24, 2008
Messages
28
Location
Edmonton, AB Canada
Hey guys,

For those who don't read in the supermoto section I've been trying to decide which bike to buy..

I rolled this off the back of my truck today..

IMG_2180.JPG


IMG_2174.JPG


IMG_2182.JPG


IMG_2183.JPG


Haven't ridden it yet.. Not nice out.. Just doing a ton of reading :)
 
nice just loose that fender & install the other fender & light that also comes with the bike when new
 
I have the other fender and light?? does it mount up nicer than the behemoth on there? :)
 
I have the same rear fender on my 05 FE 650. I thought about installing the 06 one that doesn't hang down as vertical. I went with it though and installed my plate vertical. Perfect fit. Then when I did up my blinkers I bolted on tiny flush mount Billet blinkers for the rear and they look cool. For the front I went stock blinkers, but they were a little wide for my taste so cut the steel bracket near both ends, overlapped them 1 to 2 inces on each side then welded back together.Now the fronts come out just past the platic headlight asembly.
 
Tried to mount up the other fender and tail light til I realised it's just a lens.. No actual light fixture.. So not sure how that's supposed to work.. Unless I'm missng parts..?
 
Maybe I have the wrong parts.. I'll take some pics and show ya.. It's just the red ktm lens with the nicer (shorter) fender.. The big light's assembly does not in anyway look like it's going to fit into the KTM light assembly..
 
I guess the smaller fender would look better on the supermotard, and I did like them on the enduros too. Just that I didn't seem too care enough to switch.
And my friends like the way it looks with the plate hung vertical.
 
you know, that plate fits perfect on that there mofus flap vertical. I saw pictures of the horizontal mounted plates getting ripped of by bushes. Now that was ugly!
 
I put some flush mount signals on mine
IMG_0465.jpg



****** pic I know , camera is toooo hard to figure out !
 
Everything looks pretty cool except in my opinion the plate. And for me especially, I would cover that thing in dirt in no time. My flush mount led's are similar in size and location.
 
Here's a pic. I guess the bottom line is that you need to like what you got.
 

Attachments

  • 06-29-08_1041.jpg
    06-29-08_1041.jpg
    39.7 KB
Here I am reasoning again. You know I do agree that smaller rear flap looks better. The only thing is that I want my plate hung vertical on the back of it. Do you know if it fits without hanging off the end? It looks like the plate would be a little long and I wouldn't want that .Let me know if you don't mind, otherwise I might just have to go to the dealer and measure it. Thanks
 
Yes it does but it looks fine.. MUCH better than stock.. I had cut the old light socket connector out and resplice it but no big deal :)
 
Welcome to the club

I think you need to spend some time with the cable and wiring routing around the steering head, especially the throttle cables...

They should be coming down behind the bar and triple clamp on their way to passing under the fuel tank.

Cheers

Mark
 

Similar threads

F
FE570 low idle issue, outside of the usual suspects! (I think)
Replies
2
Views
439
AussieBlue
A
BigBoreBrochacho
Hello from MN!
Replies
1
Views
456
BigBoreBrochacho
BigBoreBrochacho
T
570 engine rebuild help!
Replies
5
Views
526
TurboYoda
T
2
I have inherited an FE570, a bittersweet acquisition.
Replies
3
Views
916
269GS
2
K
AM fuel pump parts sourcing problems
Replies
1
Views
1K
o6550
o6550

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top