DIY map switch for 09-12 bent bergs

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
G

Gibbo

Joined
Jul 31, 2017
Messages
30
Location
Cairns , Australia
So after having my big 570 berg for a while and getting annoyed with how to change the rotary map switch settings i thought surely i could make something simple and effective.
So after digging around my workshop and the electronics store i came up with the following.
It was quite inexpensive considering the cost of the trailtech switch here in aus.
Anyway i'll see how well it lasts.
 

Attachments

  • 20190616_115909.jpg
    20190616_115909.jpg
    88 KB
  • 20190616_121319.jpg
    20190616_121319.jpg
    79.4 KB
  • 20190616_121322.jpg
    20190616_121322.jpg
    87.5 KB
  • 20190616_124116.jpg
    20190616_124116.jpg
    88.9 KB
Nice!
What is the electrical schema of it? Might fit into a CEV switch too, which might look equally good.
 
Well i did get the wiring diagram from a post on the site somewwhere but couldnt find the thread so i attached a copy of what i used.
i went with option A
 

Attachments

  • Map Switch Schematic.jpg
    Map Switch Schematic.jpg
    27.1 KB
Well done Gibbo. Simple effective solution to a disgustingly overpriced Trailtech switch and a pathetic rotary KTM switch.
 
Well i went and got a 3d printer and after about a year of messing about i ended up doing a remake of my map switch.
Its the same switch and wiring as above but in a much better housing.
I've made a small batch and sold a few on Facebook and thought i'd re-appear here and see if any one might want one as well.
3D printed body can be made in Black, Blue, White, Yellow, Grey, Green, Orange and Purple.

If there is some interest i can post up more details and take it from there.
 

Attachments

  • 355085902_10161339591245798_6090280841555445249_n.jpg
    355085902_10161339591245798_6090280841555445249_n.jpg
    164.5 KB
  • 20230529_214433.png
    20230529_214433.png
    383 KB
Gibbo said:
Well i went and got a 3d printer and after about a year of messing about i ended up doing a remake of my map switch.
Its the same switch and wiring as above but in a much better housing.
I've made a small batch and sold a few on Facebook and thought i'd re-appear here and see if any one might want one as well.
3D printed body can be made in Black, Blue, White, Yellow, Grey, Green, Orange and Purple.

If there is some interest i can post up more details and take it from there.
Click to expand...
Hello! Are you still willing/ wanting to sell a map switch.

I bought the Bauer switch, but was $70 USD!

How much are you selling for?
 
Hi mate,
I've been out of action for a bit being busy with work.
I'm actually in the process of making a batch of 10 and probably going to make an Ebay listing for them
I sold the 1st batch at $60 AUD with shipping anywhere in Australia. I dont know what post to the US would be
 

Similar threads

H
Buying a new FE570? Known issues, problems & common mods
3 4 5
Replies
82
Views
64K
linnell
L
D
Dale E O's 09 570
2 3
Replies
40
Views
14K
DaleEO
D
D
Dale E O's 2009 Idaho City 100 ride report
Replies
13
Views
3K
kzoo
K

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top