Head/taillights barely works with battery connected

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
T

TheTaXUS

Joined
Apr 23, 2018
Messages
17
Location
Sweden
Hi!

Bike is FE450 -06 with 550 -03 engine and swapped electrics between them after this guide: http://husaberg.org/mechanical/24974-engine-change-650-a.html
SEM stator values checked out last time I measured them.

When I have my battery connected my headlight and taillight barely works,
I have to rev quite a lot for them to shine at all. The indicators work fine though.

If I disconnect the battery the lights work with some revs but I need to rev it quite high for them to shine properly and the indicators only work sometimes.

Also my e-starter will only turn the engine one cycle.
Might have to do with the fact that I picked a 6Ah battery (completely new) instead of the recommended 8Ah.

Am I look at a bad ground or maybe a faulty voltage regulator?

Best Regards
 
Hi The TaXUS,

maybe it's two separate problems!

1. Lighting
If I'm not mistaken:
  • 2006 Kokusan Generator: 3-Phase, 150W
  • 2003 SEM Generator: 2-Phase, each 70W

Therefore both bikes had different regulator-rectifier. The newer 2004+ regulator is an all in one device, while up to 2003 the bikes had 2 different devices.
Up to 2003 the regulator/rectifier feeds the battery, the blink relay and the horn. The second phase is connected to a regulator, and direct feeds the brake light, rear light and front light! That means the rectifier is one phase only. You can rebuild the old setup on the newer wiring harness and your output should be better. But try it with a sample first before you cut all the wires, make sure the error is not somewhere else. Make sure your ground is good - that's important for every setup!


2. E-Start
The E-Start always has problems turning the engine over. There is lots of threads available about the issue. Most common is the decomp-mechanism on the camshaft gear and weak starter motors. This issue is not directly related to your wiring. You can cross check that when you wire your starter to an external 12V car batterie. Then both harnesses are separated. If you want to start it on the button - it seems to be an endless fiddle to make it reliable. Read the other posts about it first.

Regards,
EDE
 
ede said:
Hi The TaXUS,

maybe it's two separate problems!

1. Lighting
If I'm not mistaken:
  • 2006 Kokusan Generator: 3-Phase, 150W
  • 2003 SEM Generator: 2-Phase, each 70W

Therefore both bikes had different regulator-rectifier. The newer 2004+ regulator is an all in one device, while up to 2003 the bikes had 2 different devices.
Up to 2003 the regulator/rectifier feeds the battery, the blink relay and the horn. The second phase is connected to a regulator, and direct feeds the brake light, rear light and front light! That means the rectifier is one phase only. You can rebuild the old setup on the newer wiring harness and your output should be better. But try it with a sample first before you cut all the wires, make sure the error is not somewhere else. Make sure your ground is good - that's important for every setup!


2. E-Start
The E-Start always has problems turning the engine over. There is lots of threads available about the issue. Most common is the decomp-mechanism on the camshaft gear and weak starter motors. This issue is not directly related to your wiring. You can cross check that when you wire your starter to an external 12V car batterie. Then both harnesses are separated. If you want to start it on the button - it seems to be an endless fiddle to make it reliable. Read the other posts about it first.

Regards,
EDE
Click to expand...

Hi,

thanks for answering.

1. I have two of this one from when I bought the engine https://gyazo.com/5f14013acf8d119229920f4331e4eaae
Is that the one you are referring to and the one I should wire in instead of the newer one? After checking for bad ground of course.

2. The starter is from the newer 450 engine and worked fine with that one. I tried jumping the battery and it turned it over, although it was a while ago before I had assembled the tank and the rest of the wiring so if it would start it I don't know. Will try later this week since I have taken a few days off.

Best Regards
 
Hi,

your picture looks like the newer regulator that fits the kokusan-type stator. I attached a pic of the old setup for the SEM-type stator (OEM, runs fine on my bike --> ignore the bad cable connection, I already made them like new again).

Regards,
EDE
 

Attachments

  • Regulator-Rectifier_small_text.jpg
    Regulator-Rectifier_small_text.jpg
    84.7 KB
ede said:
Hi,

your picture looks like the newer regulator that fits the kokusan-type stator. I attached a pic of the old setup for the SEM-type stator (OEM, runs fine on my bike --> ignore the bad cable connection, I already made them like new again).

Regards,
EDE
Click to expand...

The one I am currently using is this one: https://gyazo.com/29bee0463b3e8fed282b6018432ec1e8

According to the parts catalog the one the -03 is using is the one I screenshoted before.
 

Similar threads

D
Battery connected in a wrong way FE 450 2009
Replies
7
Views
514
Diego
D
R
Dead flywheel?
2
Replies
31
Views
2K
Robzerg
R
F
FE570 low idle issue, outside of the usual suspects! (I think)
Replies
1
Views
420
rikschipp
R
K
AM fuel pump parts sourcing problems
Replies
1
Views
1K
o6550
o6550
S
Fe650 -02 regulator/rectifier connections
Replies
13
Views
2K
Taffy
Taffy

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top