Paolo6 a new start

Husaberg

Help Support Husaberg:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
this was the the rust on the shock we end up been in able to swap the shaft and few other parts, replace seal 20170725_113444.jpg it's been tested no leeks, it's now back to life (wasn't sure at first it could be possible but it can)


kibblewhite, porting and oversize KW valve are all in place, and now that omero is closing this might be the last shiny tank we could been able to see,
the people who carry out the work in the pictures down should be proud of themselves 20170801_144723.jpg20170801_145038.jpg20170807_105032.jpg20170807_105038.jpg

back in business few problem will come along but the worst should be gone :)
 
Last edited:
Just want to ask a question...has anyone try or seen the alpina pro carbon wheel matrix or have any feedback on them ? ...I think they can hold much more stress withouth bending/ cracking then standard full carbon also the material they using 7075 is pretty good ...any feedback is appreciated
 
Last edited:
haven't update much but i haven't forgot about this thread ...news is 16.5 and 5.5 wheel (aluminium) are on their way, I decided aluminium even if they perform slightly lower then carbon matrix for easy to fix and flex if you over jump or come shorter with the carbon I am not sure they will last you long enough

on their way also a clamp 6mm and 11mm offset

got the swingarm shorter and wider, slipper clutch

I was thinking today as I have an aluminum swingarm I can actually adapt one of those fancy ohlins or trax shock on it...even if they are longer and different bottom something can be done

as I am getting the clamp done I thought if I can chose any fork what would it be:WP cone, ohlins,marzocchi, which is more or less what you find around on ktm (and they really work well) and instead I added showa and KYB to the list

and KYB is my choice, I will be getting the husaberg with KYB :giggle:


that's how more or less the bike will look with the carbon plastic
 

Attachments

  • 20170908_192042.jpg
    20170908_192042.jpg
    91.2 KB
  • 20170918_103026.jpg
    20170918_103026.jpg
    88.9 KB
  • 20170907_111825.jpg
    20170907_111825.jpg
    95.4 KB
  • 20170907_112159.jpg
    20170907_112159.jpg
    93.9 KB
What is the size of kw valves u chose? I got 33 and 38 I think from polaris but have real problem shortening them. Many different mashine shops declined the job. One tried and never got around to it. Now I'm on mercy of yet another shop. If the can't/wont do it then I'll do it myself with grinder and small cut off disc. Have seats and guides Installed already. 33 and 38 fit really nice in the head. Would anyone consider a group buy of custom 33/38 mm kw valves? I'd be in for 5 sets myself.
 
There is a thread here with bush and also another with spanner or zaga (can't remember) with the subaru valve

The job can be done...but I have never done it or look into it ...have you try to contact KW? I am sure they have machining and knowledge to get it done or any other shop who manufacturer valves can do it

the issue is not many people have done it(probably none) and they won't take the risk

I will check this evening if I find anything about it...bush and the the guy with the subaru valve are the people to ask :)
 
paolo6 said:
haven't update much but i haven't forgot about this thread ...news is 16.5 and 5.5 wheel (aluminium) are on their way, I decided aluminium even if they perform slightly lower then carbon matrix for easy to fix and flex if you over jump or come shorter with the carbon I am not sure they will last you long enough

on their way also a clamp 6mm and 11mm offset

got the swingarm shorter and wider, slipper clutch

I was thinking today as I have an aluminum swingarm I can actually adapt one of those fancy ohlins or trax shock on it...even if they are longer and different bottom something can be done

as I am getting the clamp done I thought if I can chose any fork what would it be:WP cone, ohlins,marzocchi, which is more or less what you find around on ktm (and they really work well) and instead I added showa and KYB to the list

and KYB is my choice, I will be getting the husaberg with KYB :giggle:


that's how more or less the bike will look with the carbon plastic
Click to expand...

Hi

GGG Paolo, you are transforming this bike in a super bike !!!

And in a very expensive project :giggle:

Very nice !!

:cool:
ZAGA
 
polska said:
What is the size of kw valves u chose? I got 33 and 38 I think from polaris but have real problem shortening them. Many different mashine shops declined the job. One tried and never got around to it. Now I'm on mercy of yet another shop. If the can't/wont do it then I'll do it myself with grinder and small cut off disc. Have seats and guides Installed already. 33 and 38 fit really nice in the head. Would anyone consider a group buy of custom 33/38 mm kw valves? I'd be in for 5 sets myself.
Click to expand...

Consider when cutting/grinding your valves:
  • Are your valves filled with natrium? Opening them could be dangerous since natrium and water or drilling/grinding emulsion can cause dangerous reactions (produces hydrogen and sodium hydroxide).
  • The end of the valve shaft (valve stem face) is made from hardened steel or plated with stellite (cobalt-chrome plating) or a hardened steel pad is welded to the end.

If everything works fine and you could shorten your valve, the valve shaft end is still not hardened and wears quickly. You may could harden it using plasma nitriding... Sounds like a lot of work and a job for specialists to me...
 
Last edited:
polska--> I really don't know where to point you out apart from contacting a manufacture (give them a call sometimes they can bin email of this kind thinking you just wasting their time):( .... and brilliant ede

zaga---> It will be good (I hope so :p) ...its expensive and I never planned it, things are going forward...a bit slowly but forward

I know what to do regarding the KYB fork (conversion and stuff) there is a plan

I saw a post with bush with the KTM ohlins shock, and the ktm 85 (that was funny) , I am not 100% sure I will be able to fit it because of my exhaust,
if anyone know the shock length of the YZF 450 2010/2013 (the one with the reservoir sideway) it can seriously help me :)

slowly but forward
 
Last edited:
paolo6 said:
There is a thread here with bush and also another with spanner or zaga (can't remember) with the subaru valve

The job can be done...but I have never done it or look into it ...have you try to contact KW? I am sure they have machining and knowledge to get it done or any other shop who manufacturer valves can do it

the issue is not many people have done it(probably none) and they won't take the risk

I will check this evening if I find anything about it...bush and the the guy with the subaru valve are the people to ask :)
Click to expand...

It was spanner. Subaru ferrera valves. They are a bit smaller and required more machining work. Didn't have diamond coating. Bushmecanic sugested to remove elephants feet at the rockers, but that would mean faster wear. I want to make this build to last really long time. I'm aiming for 1000 hours before needing to open up this engine again. Meaning never again just ridem
 
polska said:
It was spanner. Subaru ferrera valves. They are a bit smaller and required more machining work. Didn't have diamond coating. Bushmecanic sugested to remove elephants feet at the rockers, but that would mean faster wear. I want to make this build to last really long time. I'm aiming for 1000 hours before needing to open up this engine again. Meaning never again just ridem
Click to expand...
uhm...tell them in the form you want the RFS valves design with the size/height you want, maybe even better send them one of your old one :happy:

Order Custom Valvetrain
Kibblewhite Precision Machining, inc - Kpmi Forms
http://nebula.wsimg.com/d45192dcd6a...EE87A1AB551A878EC&disposition=0&alloworigin=1
 
Sorry I dont recall suggesting removing the elephants feet

I suggested taking the whole foot assembly out and grinding the rocker arm so that the foot could be repositioned higher up.

With 33 38 you need longer valves anyway because they sit further toward the piston than the smaller ones

I've not done it with the polaris valves but I bet a bazillion crocksits I could do it in a weekend.
 
Looks like I misunderstood you Bushie, I never heard of elephants feet. Those are round buttons at the end of adjusting screws? So grinding rockers would simply allow me to retract adjustment further out?. I told the shop that was changing the seats and guides that I want valves to be in exactly the same position/depth as originals. I didn't want to have any surprises with the piston contact or increasing the compression ratio/reducing combustion chamber volume.
 

Attachments

  • 20170418_221329.jpg
    20170418_221329.jpg
    87.6 KB
  • 20170418_222411.jpg
    20170418_222411.jpg
    88.9 KB
shock got figure out, it can be done (ps. its a few mm longer to go well with swingarm) ...I am basically just waiting for the triple clamps.
 

Attachments

  • 20171206_143720.jpg
    20171206_143720.jpg
    83.3 KB
  • 20171206_145017.jpg
    20171206_145017.jpg
    88.8 KB
a year of work here it is

few info

-KYB POLETTI factory fork top insert 54mm bottom 59.2mm (ktm is 60) it's
been spaced, fork feet changed to suit standard husaberg (ktm) brake
-triple clamps is FAOR I can change angle (from KTM)
KTM bearing
6/7mm spacer (can't remember will measure)
it's 200mm wider so you need the 57309081000 axle
75009061000 brake spacer and need milling down to 5mm
and custom wheel spacer
-ISR master cylinder buttons work for ignition, start, kill switch
-wheel is alpina 5.5 rear and 16.5 front
-shock ohlins 5mm taller ha1684 model (just a lot shorter and revalved)
-swingarm is 2.5cm short and alu tank from tesctra (gino)
-dual exhaust ... DCR pipe system and cans is from a CRF 450
-carbonberg (pcproducts) plastic

scott steering damper got fired :) lectron carb would need some more work


just in time for summer
 

Attachments

  • 20180414_134951.jpg
    20180414_134951.jpg
    93.8 KB
  • 20180414_135256.jpg
    20180414_135256.jpg
    94.2 KB
  • 20180414_135301.jpg
    20180414_135301.jpg
    93.8 KB
  • 20180414_135305.jpg
    20180414_135305.jpg
    93.2 KB
  • 20180414_135319.jpg
    20180414_135319.jpg
    94 KB
  • 20180414_135351.jpg
    20180414_135351.jpg
    93.4 KB
  • 20180414_135413.jpg
    20180414_135413.jpg
    93.3 KB
  • 20180415_144709.jpg
    20180415_144709.jpg
    93.8 KB

Similar threads

F
FE570 low idle issue, outside of the usual suspects! (I think)
Replies
1
Views
420
rikschipp
R
E
2010 FE390
Replies
1
Views
321
ehsan
E
G
CARBURETION ADJUSTMENT PROBLEMS FE 450 2005
Replies
0
Views
52
GMC77
G
B
Spark for 2-3 seconds then nothing.
Replies
10
Views
581
mosierz48
M
D
For Sale Parting out my 2001 FE650e
Replies
6
Views
564
Danger666
D

Register CTA

Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.

Recent Discussions

Recent Discussions

Back
Top