- Joined
- Nov 20, 2001
- Messages
- 17,028
- Location
- Ely, England
Taffmeisters on Facebook
- Thread starter Taffy
- Start date
-
- Tags
- facebook taffmeisters
Help Support Husaberg:
- Joined
- Nov 20, 2001
- Messages
- 17,028
- Location
- Ely, England
Ok
just put up another video on the facebook page. i have this really nice one-owner-from-new FE600e just in and so we are playing with it and checking the ignition timing.
we also mention a little about the pilot jet and may come back to the bike and do another video after some testing.
by the way, it's a 1998 and a first time starter! we didn't do anything except set the tappets, clean the carb, new plug.
hope you like it!
facebook, Taffmeisters, Videos.
Taffy
just put up another video on the facebook page. i have this really nice one-owner-from-new FE600e just in and so we are playing with it and checking the ignition timing.
we also mention a little about the pilot jet and may come back to the bike and do another video after some testing.
by the way, it's a 1998 and a first time starter! we didn't do anything except set the tappets, clean the carb, new plug.
hope you like it!
facebook, Taffmeisters, Videos.
Taffy
- Joined
- Nov 20, 2001
- Messages
- 17,028
- Location
- Ely, England
can anyone help with the above (recent) post?
OK, two videos have just been added today
1) 2003 FS650e starting on the button from cold. not just that, it has a 2.5mm taller flat piston fitted and compression has gone from "in the nine's" to around 12 to 1.
I give it too much choke in the video......sorry!
2) How to fit the kickstart shaft along with sledge key and two different springs. this time I can't get the shaft to go down. worse than useless....what a demonstration!
regards
Taffy
OK, two videos have just been added today
1) 2003 FS650e starting on the button from cold. not just that, it has a 2.5mm taller flat piston fitted and compression has gone from "in the nine's" to around 12 to 1.
I give it too much choke in the video......sorry!
2) How to fit the kickstart shaft along with sledge key and two different springs. this time I can't get the shaft to go down. worse than useless....what a demonstration!
regards
Taffy
Here....
Attachments
- Joined
- Nov 20, 2001
- Messages
- 17,028
- Location
- Ely, England
Thanks! I trust I can find that facebook page from this right?
(later). found the Facebook page and I gather it is something to do with a Vimmerby Museum in Sweden which looks dedicated to off-road. I then checked each photo and who should be on there but David Larsson!
thanks for the link
Taffy
(later). found the Facebook page and I gather it is something to do with a Vimmerby Museum in Sweden which looks dedicated to off-road. I then checked each photo and who should be on there but David Larsson!
thanks for the link
Taffy
Last edited:
- Joined
- Nov 20, 2001
- Messages
- 17,028
- Location
- Ely, England
OK, i've just stuck up a vide on my taffmeisters facebook page about:
ROCKER ARM MAINTENANCE
about the bushes and wear
how to change tappet pads
what to do if you change the shafts to the non-oil feed type
where CFBs wear, how to make good for re-use
regards
Taffy
ROCKER ARM MAINTENANCE
about the bushes and wear
how to change tappet pads
what to do if you change the shafts to the non-oil feed type
where CFBs wear, how to make good for re-use
regards
Taffy
- Joined
- May 27, 2016
- Messages
- 138
- Location
- Portugal
Cant find the video . Can you post a link?
Enviado do meu HUAWEI Y360-U61 através de Tapatalk
Enviado do meu HUAWEI Y360-U61 através de Tapatalk
- Joined
- Feb 19, 2003
- Messages
- 3,227
- Location
- Escondido, Ca. USA
Tell Julia to start a Taffmeisters You Tube account and put all the videos up there also.
Not only will you gain massive exposure (there are hardly any Husaberg videos on You Tube) plus you will get paid if you allow ads.
Educate the brethren and make some money to boot.
Not only will you gain massive exposure (there are hardly any Husaberg videos on You Tube) plus you will get paid if you allow ads.
Educate the brethren and make some money to boot.
- Joined
- Nov 20, 2001
- Messages
- 17,028
- Location
- Ely, England
I'm aware of it Eric, we need a certain amount of followers with what we do put up and then we are given our kinda own 'chapter' for all the 'pages'.
should I start with a rant on gearing and see if i can't make it go viral. if i'm known for one thing it is 'going off on one'. and boy do i phuqin hate anyone talking about gearing. if i hear one more phuqin word said about gearing: i'm gonna rip teddies head off and his best friend jemima won't have anyone to talk too!!!!!
GOT IT!!!!!!!!!!!!!!!!
Taffy
should I start with a rant on gearing and see if i can't make it go viral. if i'm known for one thing it is 'going off on one'. and boy do i phuqin hate anyone talking about gearing. if i hear one more phuqin word said about gearing: i'm gonna rip teddies head off and his best friend jemima won't have anyone to talk too!!!!!
GOT IT!!!!!!!!!!!!!!!!
Taffy
- Joined
- Nov 20, 2001
- Messages
- 17,028
- Location
- Ely, England
Latest Video on Facebook is about reconditioning your rocker arms, its a tale of love, passion and ultimately lust. the story line is quite weak though and you can see the props moving.
the cast should be shot for their performance!
we have some special offers on this week.
there's a link to Damien Koppe's Beach race win last year.
Taffy
the cast should be shot for their performance!
we have some special offers on this week.
there's a link to Damien Koppe's Beach race win last year.
Taffy
Register CTA
Register on Husaberg Forum! This sidebar will go away, and you will see fewer ads.
Sign Up
