Husaberg
Go Back   Husaberg Forum > Lobby > New Users

New Users Post up here and introduce yourself!


Thanks Tree4Thanks
  • 1 Post By Rainerio
  • 2 Post By husabutt
  • 1 Post By Taffy
Reply
 
LinkBack Thread Tools Display Modes
May 14th, 2017, 06:16 PM   #1
Junior Member
 
Joined: Apr 2017
From: United States

Posts: 5
Thanks: 0

I Ride:
Valve clearance for a 1997 Fe 501 e

I read that the valve clearance is supposed to be 0,10mm. I'm not exactly sure what that means? Am I supposed to use the 10mm for the intake and exhaust? Is there a tolerance or is it only 10mm?
Thanks for your help.
Kilpatrick is offline  
 
May 14th, 2017, 06:58 PM   #2
Senior Member
 
Rainerio's Avatar
 
Joined: Jun 2013
From: San Francisco CA. USA

Posts: 815
Thanks: 181

I Ride: 7 Husabergs two FE570S,FS570 FE390/450,07 FE650,05 FE550,2 Husqvarna's 86 WR400,87 510,09 Buell
That's 0.10mm not 10mm. I haven't done it yet. clearance is 1/6 turn on the screw. Look at Wiki at the top of the page. Good luck
Thanks from Kilpatrick
Rainerio is offline  
May 14th, 2017, 07:05 PM   #3
Senior Member
 
husabutt's Avatar
 
Joined: Feb 2003
From: Escondido, Ca. USA

Posts: 2,943
Thanks: 259

I Ride: 2005 Fe450,2001 Fx470,1997 Fx600
The clearance between the valve shafts the adjusting screws when the engine is cold should be .12mm.

Most use the 1/6th turn method as it is difficult to get a feeler gauge into such a tight area.

On TDC on the compression stroke tighten the adjuster screw until it lightly contacts the valve shaft, then back it off 1/6th of a turn. Tighten the counternuts to 11 Newton Meters torque. Done.
Thanks from Rainerio and Kilpatrick
husabutt is offline  
May 16th, 2017, 08:12 AM   #4
Junior Member
 
Joined: Apr 2017
From: United States

Posts: 5
Thanks: 0

I Ride:
Thanks!

Thank you for your help from the both of you!
Kilpatrick is offline  
May 16th, 2017, 10:21 PM   #5
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 15,032
Thanks: 326

I Ride:
central europe writes stuff with a comma while just the UK (I thought!) use the 'sull stop' so for us 0.10mm but if english isn't your first language then it is 0,10mm.

I was 19 when i bought and raced my ducati pantah and all measurements were like that and i never, ever got used to it.

Taffy
Thanks from Kilpatrick
Taffy is offline  
Reply

  Husaberg Forum > Lobby > New Users

Tags
1997, 501, clearance, valve



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Valve clearance Husamark Mechanical 13 January 18th, 2014 07:34 PM
'10 valve clearance jlew Mechanical 3 October 21st, 2010 04:37 PM
valve clearance Facom Husaberg 0 October 10th, 2010 08:44 AM
valve clearance! pastullo Mechanical 22 February 3rd, 2009 09:46 AM
Valve Clearance gerard Mechanical 4 April 25th, 2005 04:47 PM


Facebook Twitter Google+ RSS Feed