Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Reply
 
LinkBack Thread Tools Display Modes
February 12th, 2008, 04:44 PM   #1
Junior Member
 
Joined: Dec 2007
From:

Posts: 5
Thanks: 0

I Ride:
any aftermarket valves avail.?

looking for valves,guides,seals,springs for 98 fc 501.checked kibbelwhite but only for ktm 450.what about lapping in valve-to-seat? What compound should be used?Can any one help?
bm501 is offline  
 
February 12th, 2008, 10:29 PM   #2
Senior Member
 
Joined: Jan 2007
From: Central Coast NSW Australia

Posts: 390
Thanks: 0

I Ride:
RE: any aftermarket valves avail.?

Where on the planet R U ?
I'm guessing your're on a 501?
Put your location and bike in your signature and/or profile.
Coastie is offline  
February 13th, 2008, 08:22 AM   #3
Senior Member
 
Joined: Nov 2002
From: Vacaville, California

Posts: 306
Thanks: 0

I Ride:
what is wrong with stock husaberg parts as they are good quality and not too expensive?dan
Motoxotica is offline  
February 13th, 2008, 11:28 PM   #4
Senior Member
 
Joined: Jan 2007
From: Central Coast NSW Australia

Posts: 390
Thanks: 0

I Ride:
They're damn expensive if you need the 37mm inlets !!!
Coastie is offline  
February 14th, 2008, 02:08 PM   #5
Senior Member
 
Joined: Nov 2002
From: Vacaville, California

Posts: 306
Thanks: 0

I Ride:
yes ,husaberg is proud of the 37 mm valves in the 2001-2003 bikes.fortunatly our friend does not have them.in north america the vales in an older 501 or 600 are only ~ $50 each.dan
Motoxotica is offline  
February 14th, 2008, 11:13 PM   #6
Senior Member
 
Joined: Jan 2007
From: Central Coast NSW Australia

Posts: 390
Thanks: 0

I Ride:
Yes, well he's lucky then.
Mr Husaberg can kiss my hairy butt cos I wasn't payin A$220 each for a piece of stainless crap!
I had some made for $55 bucks each and i reckon they're better than OEM.
Coastie is offline  
February 15th, 2008, 12:59 AM   #7
Senior Member
 
whosahberg's Avatar
 
Joined: Dec 2005
From: australia

Posts: 1,324
Thanks: 0

I Ride:
who charges $ 220.00 each ? ... i paid that for 4 .

oem hussaberg .
whosahberg is offline  
February 15th, 2008, 01:10 AM   #8
Senior Member
 
AUSBERG's Avatar
 
Joined: Mar 2005
From: Sunset desert/ Murray River. S.A/Victoria Australia

Posts: 514
Thanks: 3

I Ride:
Originally Posted by whosahberg
who charges $ 220.00 each ? ... i paid that for 4 .

oem hussaberg .
I think you will find hes referring to the 37mm intakes used on the earlier(pre04) engines.

I have read a thread on another site about a Toyota valve that can be used as a replacement for the 37s?- but requires shortening and collet groove machining.

Id be looking real hard at Fererra blanks and getting them machined like has been discussed here before.
AUSBERG is offline  
February 15th, 2008, 01:22 AM   #9
Senior Member
 
Joined: Jan 2007
From: Central Coast NSW Australia

Posts: 390
Thanks: 0

I Ride:
Yeah I'm talkin about the pre 04 37mm intakes - $220 each for OEM berg.
I got some made from a guy near Brisbane for $55 each.
Coastie is offline  
February 15th, 2008, 05:49 AM   #10
Senior Member
 
Joined: Apr 2004
From: Murray Sunset, Australia

Posts: 850
Thanks: 1

I Ride:
A guy in Brisbane done some for my 02 FE400 and its still going strong

Paid same as you

Probably same guy. I just sent him my old ones and he made me knew ones...
faktor is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
aftermarket, avail, valves



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
aftermarket parts stalker Husaberg 5 May 24th, 2007 09:18 AM
CLARKE 4 GALLON TANK NOW AVAIL! ncmx1 Fuel 22 April 4th, 2007 11:14 AM
Is there any aftermarket exhaust out there? HusaMike Exhausts 6 March 30th, 2007 05:04 PM
aftermarket headlight and such... risky1 Electrical 8 February 8th, 2006 12:58 AM


Facebook Twitter Google+ RSS Feed