Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Thanks Tree4Thanks
  • 1 Post By tomasnj
  • 1 Post By Taffy
  • 1 Post By Taffy
  • 1 Post By Taffy
Reply
 
LinkBack Thread Tools Display Modes
May 16th, 2021, 11:07 AM   #1
Junior Member
 
Joined: Nov 2020
From: Romania mountains

Posts: 19
Thanks: 1

I Ride: BMW F650GS ,BETA SM , Husa FE450
2004 FE450 camshaft damaged need part nr from KTM

My cam got damaged because the intake rocker arm bearing

can someone help me with the part number of the KTM camshaft that will fit to my 2004 Husaberg? i may not need high torque.... even 10-15 kw less for my weight are ok, maybe a cam from KTM400


Can I change the damaged rocker small bearing or i must buy the complete arm?

the original HUSA Husq 80036010000 is a bit expensive in my country

I am very very mystified why that small shit bearing stuck in the rocker arm that way, maybe the rocker arm was made in China ?

The oil was 10W60 1.4 Liters, even little more than necessary , also had a small amount 100 grams of aditive Liquy Moly Ceratec ..
Attached Thumbnails
2004 FE450 camshaft damaged need part nr from KTM-cam.jpg   2004 FE450 camshaft damaged need part nr from KTM-rocker.jpg  

Last edited by votkarel; May 16th, 2021 at 11:31 AM.
votkarel is offline  
 
May 16th, 2021, 01:42 PM   #2
Junior Member
 
Joined: Oct 2020
From: Iceland

Posts: 5
Thanks: 1

I Ride:
Hi votkarel

Check the price/parts on Taffmeisters, that is your best bet.

On another note, you really shouldn't put ceratec on a dirtbike - the moly (or whatever micro chemical) flakes will F-up your wet clutch. Also, I see that 300ml of ceratec are to be mixed with 5 litres of oil, hence 100ml of ceratec into 1.4 litres of oil is quite a lot.

Running more than a litre of oil on the bike will only cause problems, make sure to run the oil up to 1/3 of the oil window (when cold) the next time you are changing oil.
Thanks from votkarel
tomasnj is offline  
May 16th, 2021, 07:55 PM   #3
Junior Member
 
Joined: Nov 2020
From: Romania mountains

Posts: 19
Thanks: 1

I Ride: BMW F650GS ,BETA SM , Husa FE450
I see...
I believe last time when i adjust tappets, i didnt tighten enough the screw and after few hours the screw tighten himself and applied too much stress to the small roller



https://www.taffmeisters.co.uk/produ...roducts_id=351


i will try to find it spare part CAM here

Last edited by votkarel; May 16th, 2021 at 09:15 PM.
votkarel is offline  
May 17th, 2021, 12:06 AM   #4
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 16,502
Thanks: 612

I Ride: Husaberg FE501e 2003
the cam you want as a direct replacement is 100015.

I have just PM'd an Australian recommending a 'softer hit' at the bottom end. This is why for a time, the 380 kit was so popular.

softer hit
lower compression
softer cam
performance jetting kit (yes, really true)

the only cam softer is from the 2001-2003 FE400e which has the '01' cam fitted. I have one or two of these in stock.

anyone with a 470 reading this I would say the same thing.

cheers

Taffy
Thanks from votkarel
Taffy is offline  
May 17th, 2021, 10:27 PM   #5
Junior Member
 
Joined: Nov 2020
From: Romania mountains

Posts: 19
Thanks: 1

I Ride: BMW F650GS ,BETA SM , Husa FE450
Thx Taffy,

can I use the camshaft from 2004 husaberg 400FE ? i found someone here that break apart his bike for good price .

Last edited by votkarel; May 18th, 2021 at 06:54 AM.
votkarel is offline  
May 17th, 2021, 11:24 PM   #6
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 16,502
Thanks: 612

I Ride: Husaberg FE501e 2003
you shouldn't put a new link on an old chain.

well they never made a 400 in 2004 but if it is a late registered bike then he should be able to confirm the numbers on the end of the cam. (week)42/02........01 as an example.

regards

Taffy
Thanks from votkarel
Taffy is offline  
May 18th, 2021, 08:09 AM   #7
Junior Member
 
Joined: Nov 2020
From: Romania mountains

Posts: 19
Thanks: 1

I Ride: BMW F650GS ,BETA SM , Husa FE450
This is the donnor byke, said husaberg FE400 . its not 2004 . i believe its 2000 -2001

Will the camshaft fit to my engine 2004 , 450cc engine ?? unfortunately will ship it from another town and cannot compare it with mine... its only 40 euros that camshaft
I see that exhaust from cylinder have another shape
Attached Thumbnails
2004 FE450 camshaft damaged need part nr from KTM-husapoza.jpg  
votkarel is offline  
May 18th, 2021, 08:22 AM   #8
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 16,502
Thanks: 612

I Ride: Husaberg FE501e 2003
it looks like a 550 2006-2008

Same cam as you have now.

Taffy
Thanks from votkarel
Taffy is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
2004, camshaft, damaged, fe450, ktm, part



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
2004 FE450 camshaft advice votkarel Mechanical 2 November 17th, 2020 09:12 PM
2006 fe450 fan kit part number Hafler Cooling Systems 5 September 11th, 2017 09:32 PM
Want To Buy: Fe450 -06 Camshaft Tuuttero Want To Buy 1 September 11th, 2016 11:45 PM
For Sale: Not fore sale. Wanted: 2004-2008 Camshaft, Sprocket, Decomp Assy brucifer Classifieds 2 July 12th, 2015 06:56 PM
2004+ slipperclutch (husaberg force part) in 2002 engine? ElSnorro Mechanical 3 January 6th, 2009 01:11 PM


Facebook Twitter Google+ RSS Feed