Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Thanks Tree2Thanks
  • 1 Post By husakeits
  • 1 Post By Taffy
Reply
 
LinkBack Thread Tools Display Modes
April 4th, 2021, 12:45 PM   #1
Junior Member
 
Joined: Nov 2018
From: Rogue, River OR (USA)

Posts: 2
Thanks: 0

I Ride:
Occasional grinding noise when releasing clutch from a stop.

Hello. Tried searching but couldn't find anything on my problem. I have an '06 FE550 set up for SM. On occasion I get a grinding noise when releasing the clutch from a stop in 1st gear. Doesn't happen all the time and only from a stop. All other gear changes are fine. Seems more frequent when warmed up. I have the technical manual and couldn't find anything in the troubleshooting. I was hoping to get some guidance on diagnosing the problem.

Thanks!
Oregonian is offline  
 
April 4th, 2021, 01:17 PM   #2
Junior Member
 
Joined: Jul 2020
From: Athens,GR

Posts: 23
Thanks: 1

I Ride: 2007 FS 650 E
Is it rev a depending thing?
Say you give it more throttle to take of from a junction or less and it appears to the exact point of almost full disengagement?
Or the "meat " of the biting point?

Asking you because i get something like that very rarely in my fs650 if I am hesitant with the release of the clutch. And my mechanic said it's normal .
husakeits is offline  
April 4th, 2021, 01:23 PM   #3
Junior Member
 
Joined: Nov 2018
From: Rogue, River OR (USA)

Posts: 2
Thanks: 0

I Ride:
Originally Posted by husakeits View Post
Is it rev a depending thing?
Say you give it more throttle to take of from a junction or less and it appears to the exact point of almost full disengagement?
Or the "meat " of the biting point?

Asking you because i get something like that very rarely in my fs650 if I am hesitant with the release of the clutch. And my mechanic said it's normal .
Amount of throttle doesn't seem to matter and although I haven't put a bunch of hours on this bike it has just recently started. Noise seems to come on about mid point of clutch release through full release.
Oregonian is offline  
April 4th, 2021, 02:56 PM   #4
Junior Member
 
Joined: Jul 2020
From: Athens,GR

Posts: 23
Thanks: 1

I Ride: 2007 FS 650 E
Mine pretty much stopped doing it afte the engine rebuild. It has done it once again after the 25 hr mark. Open the clutch cover and measure if everything is in spec disc, plates etc. If it is and the hydraulic pump - slave is in good condition with fresh fluid and no leaks ,I would forget it and move on.
Thanks from Oregonian
husakeits is offline  
April 5th, 2021, 02:32 AM   #5
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 16,417
Thanks: 582

I Ride: Husaberg FE501e 2003
always thought it was the clutch drum. check the part number on it finishes ......500 and not 200 or 250.

Taffy
Thanks from Oregonian
Taffy is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
clutch, grinding, noise, occasional, releasing, stop



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Clutch Noise FE 650 Tamas Mechanical 7 January 2nd, 2013 08:16 AM
Occasional Misfire - Help! hlambourn Mechanical 5 December 15th, 2011 11:50 AM
Anyone managed to stop clutch squeel? philis Mechanical 15 February 6th, 2011 07:21 AM
clutch noise.. chad A Mechanical 11 June 14th, 2010 12:13 AM
98 FE501 Grinding noise coming from clutch Goblox Mechanical 1 January 7th, 2010 09:46 PM


Facebook Twitter Google+ RSS Feed