Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Thanks Tree1Thanks
  • 1 Post By gamer3210
Reply
 
LinkBack Thread Tools Display Modes
November 28th, 2020, 03:09 PM   #1
Junior Member
 
Joined: Nov 2020
From: VT

Posts: 1
Thanks: 0

I Ride:
1995 FE350 Timing and TDC

Replacing the cam shaft bearings on my 350.
Anyone have any tips on location TDC I don't see any marks on the flywheel
Thanks
matti boy is offline  
 
November 29th, 2020, 02:40 AM   #2
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 16,336
Thanks: 556

I Ride: Husaberg FE501e 2003
use the dead stop method. put it in a search.

finding top dead centre using the dead stop method.

I have a bit of stud here, that means threaded rod thast is all rod, no shank, no head OK? I push it in the hole and lock it over to one side so it hooks into the bottom thread of the spark plug hole. I then bring the piston up on the slywheel using a 17mm STEPPED ring spanner. you must control the flywheel against the valve springs!

don't crash into the stud. just tap it and then mark the flywheel with a thin tipped felt-tip pen. then go the other way. you learn very quickly that you're stopping the piston too far down so bring the stud up. in the end, when the two marks are 40-60mm apart it is easy to disect the middle of the two marks, wope the others away. you have TDC.

there's a mark on the crankcase at about 10 o clock on the interface of the cases to the ignition cover.

I don't like using it but it is there. I prefer my own mark under the top ignition cover bolt hole.

Taffy
Taffy is offline  
December 1st, 2020, 12:53 AM   #3
Member
 
Joined: Nov 2019
From: Warszawa

Posts: 38
Thanks: 3

I Ride: HUSABERG FC 600 98 HUSABERG FC 600 00 Husqvarna Tc 610 94 husaberg fe 501 93 ,Honda Crf 450 04
I set the piston up and mark where the piston starts to go down by turning the wheel to the right and turning it left, then I have 2 lines and mark the center of these lines in each 4t, I set it and it's 100%
Thanks from Rainerio
gamer3210 is offline  
December 1st, 2020, 02:20 AM   #4
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 16,336
Thanks: 556

I Ride: Husaberg FE501e 2003
yes that's the way!

cheers

taffy
Taffy is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
1995, fe350, tdc, timing



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
1995 fe350 electrical help!! Kurbz Electrical 4 May 6th, 2020 11:42 PM
My New to me 1995 FE350 tdo2613 Husaberg 1 August 20th, 2019 09:15 PM
Setting timing on 1992 FE350 - am I doing this right? joef Mechanical 7 April 9th, 2016 01:17 AM
adjusting timing with a dial back timing light? mrk3cobra Electrical 6 November 1st, 2008 06:17 AM
1995 Fe 501 Help? SndyRds Husaberg 5 January 23rd, 2005 10:49 PM


Facebook Twitter Google+ RSS Feed