Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Thanks Tree1Thanks
  • 1 Post By mars
Reply
 
LinkBack Thread Tools Display Modes
October 19th, 2020, 11:23 AM   #1
Junior Member
 
Joined: Oct 2020
From: Portugal

Posts: 17
Thanks: 0

I Ride:
Cylinder( Help )

My cylinder is well assembled, the bikes 400 Fe 2003 does not have any brand to run the cylinder, is closed and is losing water , I think it is very strange someone can tell me what is passing the joint is original Husaberg , the cylinder must be bad
Attached Thumbnails
Cylinder( Help )-colassa.jpg   Cylinder( Help )-motor-aberto.jpg   Cylinder( Help )-motor-agua.jpg  
Xinasa is offline  
 
October 20th, 2020, 04:01 AM   #2
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 16,265
Thanks: 539

I Ride: Husaberg FE501e 2003
take it off and have a look but this is rare.

Taffy
Taffy is online now  
October 20th, 2020, 08:56 AM   #3
Member
 
mars's Avatar
 
Joined: Jun 2004
From: denton texas

Posts: 79
Thanks: 7

I Ride: 2010 KTM250SX, 2001 Husaberg FC550
I have had coolant leakage problems in the past. Once was incorrect water passage O-ring installed between clutch case and center case. So from that time on after rebuild I would pressurize the motor coolant system 15-20pis, then check for leaks, with soapy water. My last rebuild I had gas passing around the head to cases, very little but leaking. After trying a other new head gasket which did not help, I used Permatex Copper Spray-A-Gasket which has stopped the leakage, now the cooling system can hold its 15psi for 24hrs.

Mars
Husaberg FC550 2001 Original owner.
mars is offline  
October 20th, 2020, 10:01 AM   #4
Junior Member
 
Joined: Oct 2020
From: Portugal

Posts: 17
Thanks: 0

I Ride:
What are the dimensions of the original o'ring of the husaberg cylinder
Xinasa is offline  
October 22nd, 2020, 02:54 PM   #5
Member
 
mars's Avatar
 
Joined: Jun 2004
From: denton texas

Posts: 79
Thanks: 7

I Ride: 2010 KTM250SX, 2001 Husaberg FC550
Xinasa,

The coolant passage O-ring between the clutch case cover and the center cases is 17.3 x 2.4mm NBR.

Mars
Husaberg FC550 2001
Thanks from Goose916
mars is offline  
October 22nd, 2020, 04:38 PM   #6
Junior Member
 
Joined: Oct 2020
From: Portugal

Posts: 17
Thanks: 0

I Ride:
Thank
Xinasa is offline  
October 26th, 2020, 10:35 AM   #7
Junior Member
 
Joined: Oct 2020
From: Portugal

Posts: 17
Thanks: 0

I Ride:
Does anyone know the measurements of the oring (OEM) of the husaberg 400 Fe cylinders
Xinasa is offline  
October 26th, 2020, 10:38 AM   #8
Junior Member
 
Joined: Oct 2020
From: Portugal

Posts: 17
Thanks: 0

I Ride:
imagem
Attached Thumbnails
Cylinder( Help )-motor-aberto.jpg  
Xinasa is offline  
October 28th, 2020, 02:09 PM   #9
Junior Member
 
Joined: Oct 2020
From: Portugal

Posts: 17
Thanks: 0

I Ride:
In cylinders from 2001 to 2003 the cylinder covers this hole. the compression is tuda to go back.. I took off the cap to put the oil with the bike to work sends the whole oil out .
Attached Thumbnails
Cylinder( Help )-furo-de-carter-.jpg  
Xinasa is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
cylinder



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
96 fc 600 cylinder ragrobb Mechanical 0 October 29th, 2011 10:39 AM
cylinder head spiney Mechanical 6 September 7th, 2008 12:17 AM
cylinder i96rcr Mechanical 1 February 27th, 2007 10:18 PM
cylinder sleeve BelgiqueBasterd Mechanical 9 November 21st, 2006 03:39 AM
Cylinder Mika Mechanical 2 August 15th, 2005 02:56 PM


Facebook Twitter Google+ RSS Feed