Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Thanks Tree3Thanks
  • 2 Post By NoClassic
  • 1 Post By manwithgun
Reply
 
LinkBack Thread Tools Display Modes
March 21st, 2020, 02:45 AM   #1
Junior Member
 
Joined: Jun 2013
From: awe

Posts: 3
Thanks: 0

I Ride:
Is 2012 really 2011???

Hi all,

I'm having issues with my 2012 FE390, it's actually impossible to get it into neutral when its running even using my hand I can't do it. The bike was working fine previously but has not been used in around 12 months and i've only had the issue since then. I replaced the clutch master cylinder seals and spent hours bleeding it from both ends but still seems to be the same. I'm figuring it might be the slave seals? I was going to order a set but the ones I see listed are all for FE390 up to 2011, Isn't this the same model as the 2012??

If anyone has any other suggestions they would be greatly appreciated the bike only has about 90 hours and I do have a rekluse fitted (the ball bearing one) I opened the cover up and checked the gaps as per the rekluse manual and all seems good.

Thanks
Potter is offline  
 
March 22nd, 2020, 01:49 PM   #2
Member
 
Joined: May 2017
From: United States

Posts: 68
Thanks: 14

I Ride:
2011 and 2012 will have the same part.

The slaves fail with pretty good frequency and the two times it happened to mine it was after the bike sat over the off season. The factory seals will continue to fail in time. Save yourself continued headaches and buy the rekluse or oberon slave cylinder.
Thanks from Rainerio and TXThumper
NoClassic is offline  
March 29th, 2020, 04:21 PM   #3
Junior Member
 
Joined: Jul 2018
From: HB

Posts: 1
Thanks: 1

I Ride: 2010 FE450
Clutch drag and difficulty finding neutral at a stop is common with these bike but less of an issue with electric start. Neutral is easier to find when still rolling forward or by blipping the throttle and shifting while the rpms dropping. If the clutch slave was leaking, you'd eventually notice a loss of mineral oil from the reservoir @ master. Husaberg only lists the entire piston assembly but just the piston O-ring can be replaced with KTM #54832067000 for $2. External O-ring is KTM #077030005 and gasket is #59032065000. So $5 gets you back to stock trim if the bore is not grooved, but the Magura will still be prone to failure. Seals can be replaced with a 5mm allen and snap-ring pliers. Light weight suspension fluid can be used if you don't want to purchase Magura Blood.
Thanks from NoClassic
manwithgun is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
2011, 2012, clutch



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
2011 vs 2012 570 genefewings New Users 6 November 26th, 2015 05:33 PM
Sold my 2011 FE390...looking at 2012 TE300...specific issues to look for? doolin64 Husaberg 5 January 13th, 2015 06:11 AM
New 2011 & 2012 Husaberg Motorcycle 55 Watt HID Headlight pw_garfield Marketplace 55 June 6th, 2013 09:18 AM
Difference USA FE 390 2009 2010 2011 2012 ninayu61 Mechanical 1 March 15th, 2012 12:39 PM
2011 BERGS IN STOCK! ALL PRE 2011 ON CLEARANCE SALE! renoktm Marketplace 0 September 18th, 2010 12:22 PM


Facebook Twitter Google+ RSS Feed