Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Reply
 
LinkBack Thread Tools Display Modes
July 7th, 2019, 05:42 AM   #11
Junior Member
 
Joined: Jun 2019
From: Alameda, CA

Posts: 21
Thanks: 3

I Ride:
I got a clarification that it wasn't so much shavings as just some fuzz on the magnet.

Regarding the clutch, there's probably at least an inch of free play. I'm assuming that isn't normal. Between that and the condition of the master, I imagine something has failed.
Junkie is offline  
 
July 8th, 2019, 05:59 AM   #12
Junior Member
 
Joined: Jun 2019
From: Alameda, CA

Posts: 21
Thanks: 3

I Ride:
The part # for the clutch slave is 75032061044 (at least on Munn's fiche)

Oberon lists a unit for that

https://www.cjdesignsllc.com/about-u...ch-slave-unit/ states that it fits a bunch of KTMs, including all the smaller bikes and 690s (although I assume not the new ones)

does anyone run one? given that it appears to be a common point of failure I'd rather go with something less prone to problems.
Junkie is offline  
July 8th, 2019, 08:46 AM   #13
Member
 
Joined: May 2017
From: United States

Posts: 43
Thanks: 8

I Ride:
I have read multiple reports of people finding metal on their drain plug/pickup screen with low hour oil changes. If the motor is otherwise performing well and not making noise it is likely fine.

Just go ahead and buy the Oberon clutch slave. The factor seals will continue to fail or at least that is my personal experience after replacing a few.

Last edited by NoClassic; July 8th, 2019 at 08:49 AM.
NoClassic is offline  
July 8th, 2019, 09:07 AM   #14
Junior Member
 
Joined: Jun 2019
From: Alameda, CA

Posts: 21
Thanks: 3

I Ride:
Apparently it was very fine, which is part of why I bought it.

I'll be putting maybe an hour on it, dumping the oil, and seeing what I get. Don't want to do any more damage than has already happened but also don't want to waste money.

Is there a common clutch master upgrade, given the condition of mine, or should I rebuild it?
Junkie is offline  
July 8th, 2019, 02:02 PM   #15
Member
 
Joined: May 2017
From: United States

Posts: 43
Thanks: 8

I Ride:
http://www.oberon-performance.co.uk/...C4-Models.html

There are a few options but the Oberon would be my pick. The model made for the LC4 KTMs fits the 70 degree motors.

You can try rebuilding yours but mine failed twice after replacing the factory seal. Mine showed no signs of scoring on the piston or housing and I was using the proper mineral oil based fluid.
NoClassic is offline  
July 8th, 2019, 02:14 PM   #16
Junior Member
 
Joined: Jun 2019
From: Alameda, CA

Posts: 21
Thanks: 3

I Ride:
I'd found the slave, and am planning on going that way. Given that it looks like my master has failed, I was wondering whether there's an upgrade at that end too.
Junkie is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
2011, fs570, producing, shavings, steel, wrong



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale: 2011 fs570 heman Classifieds 2 November 13th, 2017 04:19 PM
For Sale: 2011 fs570 Capeters Classifieds 14 September 30th, 2016 05:09 AM
2011 FS570 Stalling SLOBRA Husaberg 8 May 27th, 2013 01:16 AM
2011 FS570 - Can't get GAS CAP off husabergwannabe Husaberg 3 May 20th, 2012 08:11 AM
Looking for a 2011 FS570.... rbott Husaberg 2 March 19th, 2012 03:01 PM


Facebook Twitter Google+ RSS Feed