Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Thanks Tree4Thanks
Reply
 
LinkBack Thread Tools Display Modes
July 29th, 2018, 11:29 AM   #21
Junior Member
 
Dan0995's Avatar
 
Joined: Jul 2016
From: Rawdon, Quebec, Canada

Posts: 29
Thanks: 3

I Ride: Husaberg 450fe 06, Honda CBR 600RR 04
Hi Guys,

The bike run great. Full trottle the engine sound is clean. Only a few back fire going downhill, don't know if it normal.

My only problem is it stall after a few minute or right after I keep the gas full trottle a few second. Seems fine at low idle.

My question is, could it be my valve adjustment the problem? I had this issue before adjusting the valve.
spark plug is new, the head is 100% rebuild with taff's parts.
I'll replace the spark plug cap and make a second run.

thanks!

Daniel
Dan0995 is offline  
 
July 29th, 2018, 04:36 PM   #22
Junior Member
 
Dan0995's Avatar
 
Joined: Jul 2016
From: Rawdon, Quebec, Canada

Posts: 29
Thanks: 3

I Ride: Husaberg 450fe 06, Honda CBR 600RR 04
Problem solved, I have a weak gas flow probably cause by the gas valve from my second tank.

Many thanks for your help and patience.
Attached Thumbnails
Valve adjusment Husaberg 450fe 06-img_20180729_191719.jpg  
Thanks from tourist
Dan0995 is offline  
August 8th, 2019, 08:17 PM   #23
Member
 
Joined: Jul 2019
From: Ontario

Posts: 43
Thanks: 1

I Ride: 97 KTM SX 250 2 stroke and 04 husaberg 450fe
Originally Posted by Dan0995 View Post
Start after the second try. Nice idle, No back fire. Will try it tomorow if I was on the TDC this time
Hey did you have any issues with your valves after using this method with the flywheel bump at 9 0 clock ? I'm in middle of doing mine for first-time
Chrisfe450canadian is offline  
August 9th, 2019, 02:26 AM   #24
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 15,769
Thanks: 462

I Ride: Husaberg FE501e 2003
as a GOLDEN RULE to finish this tappet thread off;

I discovered from my mechanics that they also struggled to get the valve clearances right. sure, they'd get a 1/6th-of-a-turn but the tappets were way too tight and the bikes didn't run right.

YOU MUST BE ABLE TO GRAB THE LOCKNUT WITH THE TIPS OF YOUR FINGER AND MAKE MORSE CODE NOISES. THAT NOISE MUST JUST BE AUDIBLE AT THE REAR LICENSE PLATE HOLDER....JUST....NO FURTHER.....NO LESS.

adjust and loosen till you get this noise - JUST at the rear light/plate holder.

Taffy
Taffy is online now  
August 9th, 2019, 07:15 PM   #25
Junior Member
 
Dan0995's Avatar
 
Joined: Jul 2016
From: Rawdon, Quebec, Canada

Posts: 29
Thanks: 3

I Ride: Husaberg 450fe 06, Honda CBR 600RR 04
Chris, The bike run like a charm after adjusting the valve. My initial problem was the gas valve on the auxiliary tank almost closed with the vibration.

Thanks again Taffy!
Dan0995 is offline  
August 9th, 2019, 07:45 PM   #26
Member
 
Joined: Jul 2019
From: Ontario

Posts: 43
Thanks: 1

I Ride: 97 KTM SX 250 2 stroke and 04 husaberg 450fe
Originally Posted by Dan0995 View Post
Chris, The bike run like a charm after adjusting the valve. My initial problem was the gas valve on the auxiliary tank almost closed with the vibration.

Thanks again Taffy!
glad to hear. Is this right position on flywheel? Pic is sideways do I align the bump at 9 o'clock bolt on the compression stroke then that's where I'd asjust the valves ?
Attached Images
 
Chrisfe450canadian is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
450fe, adjusment, husaberg, valve



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Clicker Adjusment Ryno570 Suspension 5 May 2nd, 2017 03:23 AM
husaberg 450fe 2011 FLAN4 Fuel 3 July 2nd, 2012 07:56 PM
Husaberg 450fe 2003 wont rev mansa Mechanical 34 April 20th, 2012 03:16 PM
450FE-09 valve adjustment? garthfin Mechanical 5 February 22nd, 2009 09:09 AM
05 450fe or 08 450fe? is the price difference worth it? cookymonsta Husaberg 14 February 19th, 2008 12:28 PM


Facebook Twitter Google+ RSS Feed