Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Reply
 
LinkBack Thread Tools Display Modes
April 9th, 2017, 12:19 PM   #1
Junior Member
 
Joined: Apr 2017
From: Poland

Posts: 7
Thanks: 0

I Ride:
FC 600 problem, after change timing chain.

Hello,
One week ago i bouhgt husaberg fc 600.
I think its 1995y.

Before my mods it was hard to start engine, when it start running moto doesnt want to go upper rpm, only shooting from the exhoust.

I had to change timing chain, coz old one was very long.

For now husaberg dont want to start, i set up valves 0.1 mm, carb cleaned and setuped with Service manual.

I dont know what goin on... Anyone have suggestions?
http://cloud.tapatalk.com/s/58ea9743...18559033.jpeg?


Wysłane z mojego GT-I9305 przy użyciu Tapatalka
lukax123 is offline  
 
April 9th, 2017, 12:57 PM   #2
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 15,032
Thanks: 326

I Ride:
you need to check the valve timing. I suggest that you remove the rocker cover and the spark plug and put a dial gauge in the top with a little 2mm rod in the end of the dial gauge. (you can see this in one of my videos in may facebook page). get both lobes to the top. when you are sure it is the REAL TDC you must check that the cam lobes are like Mickey Mouse's ears.

when you do the valve clearances make sure you do the '1/6th of a turn' method. you must hear the tappets 'morse code' by the rear wheel.

set the ignition to the middle of the adjustment.

your engine is 1997-1998.

regards

Taffy
Taffy is offline  
April 9th, 2017, 07:02 PM   #3
Member
 
Joined: Aug 2016
From: USA

Posts: 39
Thanks: 13

I Ride: 99 FC600, 95 FC501, 94 FE501
What oil are you running? Since you just bought this bike, I would change the oil, if you have not already done so. In the last picture, the oil residue on the cam chain looks disturbingly like ATF.
VOR165 is offline  
April 9th, 2017, 11:49 PM   #4
Junior Member
 
Joined: Apr 2017
From: Poland

Posts: 7
Thanks: 0

I Ride:
Fine, checking timing one more time.

Running on motul 7100 full synthetic.

Ty for reply

Wysłane z mojego GT-I9305 przy użyciu Tapatalka
lukax123 is offline  
April 10th, 2017, 01:33 AM   #5
Junior Member
 
Joined: Apr 2017
From: Poland

Posts: 7
Thanks: 0

I Ride:
Its tdc, and timing looks like that.
Everything ok FC 600 problem, after change timing chain.-20170410_113008.jpgFC 600 problem, after change timing chain.-20170410_113015.jpgFC 600 problem, after change timing chain.-20170410_113036.jpg

Wysłane z mojego GT-I9305 przy użyciu Tapatalka
lukax123 is offline  
April 10th, 2017, 02:24 AM   #6
Junior Member
 
Joined: Apr 2017
From: Poland

Posts: 7
Thanks: 0

I Ride:
I checkd timing, and it couldnt be in another setup...

Wysłane z mojego GT-I9305 przy użyciu Tapatalka
lukax123 is offline  
April 10th, 2017, 02:40 AM   #7
Junior Member
 
Joined: Apr 2017
From: Poland

Posts: 7
Thanks: 0

I Ride:
Probalby its not timing problem, i checkd stator coil, and with good hard kick is only 12volts

Wysłane z mojego GT-I9305 przy użyciu Tapatalka
lukax123 is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
600, chain, change, problem, timing



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem with timing chain length and capacity lukax123 Mechanical 2 April 5th, 2017 12:52 PM
97 501 timing chain Sgtx Mechanical 17 February 16th, 2017 03:48 PM
Old cam timing sprocket (98) change zaga Mechanical 5 August 4th, 2014 04:55 AM
new chain - should I change sprockets? kipper Husaberg 4 November 20th, 2011 02:02 PM
How many have the timing chain problem? (Year 2009) Mrpwr Mechanical 1 January 30th, 2009 01:41 AM


Facebook Twitter Google+ RSS Feed