Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Thanks Tree1Thanks
  • 1 Post By hofsviken
Reply
 
LinkBack Thread Tools Display Modes
January 28th, 2017, 04:32 AM   #1
Member
 
Joined: Nov 2016
From: Norway

Posts: 32
Thanks: 2

I Ride: FS650 02 mod, Honda Cr125 92 mod, Yamaha Raptor 350 06 mod
Camshaft bearings 650 02

Hi!

I have pressed in new bearings on the camshaft on my 650 Berg. I read somewhere in the manual that the bearing should be pressed in so you just got a little clearance between the bearing and the auto decomp device. But I cant find any information on how far pressed in the other bearing should be.

Should that be pressed in so it is bottoms in the cam shoulder? If i do, I think it looks like the cam sprocket are not in the accurate centerline between the two cam sprockets.

Andreas
hofsviken is offline  
 
January 28th, 2017, 06:39 AM   #2
Moderator
 
ned37's Avatar
 
Joined: Dec 2004
From: back in cottonwood, az

Posts: 2,389
Thanks: 215

I Ride: '08 HUSKY te610
every one i have done got seated. no problem
ned37 is offline  
January 28th, 2017, 11:19 AM   #3
Senior Member
 
bushmechanic's Avatar
 
Joined: Jun 2007
From: south east WA Australia

Posts: 3,868
Thanks: 1215

I Ride: 2008 700FK, 2002 628FST
its true the cam sprockets often dont line up

so if you can use the cam bearing placement to correct sprocket alignment without interfering with the decomp then go for it

i used washers to make sure the cam bearings didn't move and did some machining to the cam shoulder
bushmechanic is offline  
January 30th, 2017, 07:18 AM   #4
Member
 
Joined: Nov 2016
From: Norway

Posts: 32
Thanks: 2

I Ride: FS650 02 mod, Honda Cr125 92 mod, Yamaha Raptor 350 06 mod
Yes, thats what i did also. Pulled the bearing a little out from the camshoulder and a washer in between. I think it is weird that the manual dont say anything about it, as it is a important thing considering sprockt/chain wear and the load on the cam bearings.
Thanks from bushmechanic
hofsviken is offline  
January 31st, 2017, 04:59 AM   #5
Moderator
 
ned37's Avatar
 
Joined: Dec 2004
From: back in cottonwood, az

Posts: 2,389
Thanks: 215

I Ride: '08 HUSKY te610
my oem '04 450 bearing on the sprocket side was loose enough to find a center on it's own
ned37 is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
650, bearings, camshaft



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
only camshaft fe 450 04 Mario Mechanical 3 November 9th, 2014 02:17 PM
camshaft bearing RZmike95 Mechanical 9 May 10th, 2012 11:38 PM
'07 FS 650 E Camshaft nitzi Mechanical 4 November 25th, 2010 04:41 AM
LRX2 Camshaft gotlund Mechanical 5 March 4th, 2010 02:17 AM
Camshaft Lobes up or Down at TDC ADryden23 Mechanical 4 June 27th, 2009 02:24 PM


Facebook Twitter Google+ RSS Feed