Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Reply
 
LinkBack Thread Tools Display Modes
May 21st, 2014, 09:38 AM   #1
Junior Member
 
Joined: Oct 2013
From: Finland

Posts: 13
Thanks: 0

I Ride: KTM 450 & 525 EXC, Husa 650, Honda ST70
Engine noise?

Anyone who has experience of the 650 egine sounding like this??

Noisy Husaberg - YouTube
Finnmats is offline  
 
May 21st, 2014, 02:33 PM   #2
Junior Member
 
hyebo's Avatar
 
Joined: Oct 2012
From: Madrid

Posts: 28
Thanks: 2

I Ride:
Think that your noise its diferent what i had here



But just in case in real sound like that my problem it was just a bad clearance valve so i just adjust them and the noise gone.
hyebo is offline  
May 22nd, 2014, 10:38 AM   #3
Junior Member
 
Joined: Oct 2013
From: Finland

Posts: 13
Thanks: 0

I Ride: KTM 450 & 525 EXC, Husa 650, Honda ST70
hyebo, you have typhical valve noise, but this is not that! This is more a "whistling" noise, that sounds like it's coming from the waterpump/clutch/smaller bearing... Amyone???
Finnmats is offline  
May 24th, 2014, 02:09 PM   #4
Member
 
mars's Avatar
 
Joined: Jun 2004
From: denton texas

Posts: 63
Thanks: 3

I Ride: 2010 KTM250SX, 2001 Husaberg FC550
engine noise

My 2001 FC550, counter balance bearing (single row bearing) failed. The sound was close to yours. But I think after 2003 the counter balnace bearing was a double row bearing with none or little failures.

Just before the failure of the bearing I started to find more than normal metal chips in the oil.

So possible time for a tear down.

MARS

2001 Husaberg FC550

KTM 250SX 2010

KTM 2013SX 2013
mars is offline  
May 25th, 2014, 01:22 AM   #5
Junior Member
 
Joined: May 2014
From: Bathurst

Posts: 1
Thanks: 0

I Ride:
Ive got a 2006 model 650 that died about four years
Ago and ive been too afraid to get the wallet out and
Start fixing it. Although i know the basics of the start
Of the problem, the nut on the primary gear came loose
Of which in turn caused the keyway to give way splitting the
Primary (pinion) gear to crack in two. It had only done 50hrs
But i am yet to find out if the valves would have flapped freely
And caused damage or if i can just patch the shaft and replace
the gear. Pull the left cover off to check, cheers!
BathurstBerg is offline  
May 20th, 2017, 12:18 PM   #6
Junior Member
 
Joined: May 2017
From: Finland

Posts: 1
Thanks: 0

I Ride: Fs550e -08
Exclamation

Was this (whining noise) problem solved!? Cause i Have same problem right now.

Last edited by KILLNWO; May 20th, 2017 at 12:40 PM.
KILLNWO is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
engine, noise



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
engine noise when hot netrac Mechanical 15 May 16th, 2013 01:49 PM
engine noise? thunderbucky Tech 5 April 1st, 2011 12:32 PM
engine noise fordfasterr Mechanical 4 July 1st, 2007 01:10 PM
engine noise ASMACSBOB Mechanical 4 February 2nd, 2005 08:10 PM
noise from engine? jacko Mechanical 5 November 17th, 2004 12:09 PM


Facebook Twitter Google+ RSS Feed