Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Mechanical

Mechanical Mechanical Forum - spinning bits and gyrating bobs


Reply
 
LinkBack Thread Tools Display Modes
December 29th, 2012, 10:47 AM   #1
Junior Member
 
Joined: Oct 2012
From:

Posts: 6
Thanks: 0

I Ride:
bottom end noise

recently my fe550 2007 berg has started to make a whining noise from the bottom end both sides.after an oil change i noticed oil on the drain plug and some relly small fileings in the oil.im ssupecting main bearings beginning to say bye bye.and anyone ane idea of the parts required to replace them??havnt long got it and unsure of the history so gimme the bad news

Cheers
rocket8 is offline  
 
December 31st, 2012, 01:16 AM   #2
Junior Member
 
Joined: Jan 2010
From: Vilnius

Posts: 4
Thanks: 0

I Ride: FE450
Re: bottom end noise

When I heard unusual noise after I saw this:



and I found this



then all you need unusual is that special tool for removing THAT bearing



584.29.037.037 MOUNTING TOOL INNER RING NJ206

Nothing bad if fixed in time. And in my case the reason probably was not correct bearings - same size but different.
Good luck and Happy New Year!
Rammst is offline  
January 2nd, 2013, 02:48 AM   #3
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 15,380
Thanks: 394

I Ride: Husaberg FE501e 2003
Re: bottom end noise

Originally Posted by rocket8
recently my fe550 2007 berg has started to make a whining noise from the bottom end both sides.after an oil change i noticed oil on the drain plug and some relly small fileings in the oil.im ssupecting main bearings beginning to say bye bye.and anyone ane idea of the parts required to replace them??havnt long got it and unsure of the history so gimme the bad news

Cheers
sounds about right I'm afraid. mains.

oil changes have to be every 6-8 hours especially if you start it and don't ride.

you'll need mains, gasket set, a camchain probably?, little end can be dodgy, i'm going to guess and say that the liner will look rough so that is a re-nikasil and new 'A' piston. waterpump seal, grope around the gearbox bearings (the three balls), a new filter, check the tappet pads for cupping,

upgrades
ADC spring
DVSK
starter repair kit

should be about all you need?

regards

Taffy
Taffy is offline  
January 2nd, 2013, 12:17 PM   #4
Junior Member
 
Joined: Oct 2012
From:

Posts: 6
Thanks: 0

I Ride:
Re: bottom end noise

cheers taffy.can u give me a price?.can you deliver to northern ireland.
regards.
rocket8 is offline  
January 2nd, 2013, 04:33 PM   #5
Senior Member
 
Bergini's Avatar
 
Joined: May 2011
From: Wisconsin, U.S.

Posts: 700
Thanks: 3

I Ride: 1995 dakota 408 5spd 8 3/4 rear end
Re: bottom end noise

reguarding the bearing in the pic.....

i would cut a deep groove in it with a cutoff wheel then hit it with a chisel and crack it, it will come right off.......just dont touch the gear and dont cut all the way through into the crank, obviously you cant cut straight across......another possiblity would be to cut notches for a puller to grip it and apply heat as needed during removal.

screw the tool....

disclaimer: The unsteady or unpatient hand should not attempt
Bergini is offline  
January 2nd, 2013, 11:40 PM   #6
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 15,380
Thanks: 394

I Ride: Husaberg FE501e 2003
Re: bottom end noise

a couple of ways I've dealt with them

1) grind the bitch down to a millimitre on one side then it loses all its strength.
lots of careful washing needed afterwards.

2) heat it up with a couple of men on gas torches, then with a flat-bladed screwdriver start whacking them in from each side.
very few people know what size screwdriver does the job or which size hammer is safe or what is holding it up where and why......

option 1 with a 4" grinderrette is my best choice for the novice.

regards

Taffy
Taffy is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Mechanical

Tags
bottom, end, noise



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Fe550 weird clunking noise in bottom end matfew Mechanical 5 September 24th, 2012 11:51 AM
Noisy bottom end adz97 Mechanical 3 August 17th, 2012 10:04 AM
top & bottom yokes RejekzNoodles Suspension 2 July 11th, 2011 10:17 AM
Oil in the bottom of the sock ajw30 Fuel 3 December 18th, 2010 03:24 AM
pds bottom balljoint flatchat Suspension 9 April 18th, 2007 10:48 AM


Facebook Twitter Google+ RSS Feed