Husaberg
Go Back   Husaberg Forum > Husaberg Forum > Husaberg

Husaberg Husaberg Forum - Husaberg Motorcycle Forum


Reply
 
LinkBack Thread Tools Display Modes
September 4th, 2007, 01:09 AM   #1
Junior Member
 
Joined: Jun 2002
From: Bled, Slovenia

Posts: 26
Thanks: 0

I Ride:
Carburettor settings

Hello.

I had to put apart a carburettor (Dellorto) of my 2001 FS650e.
Unfortunately, I have lost my notes about idling and mixture screw settings.

Does anybody know the approximate settings (how many turns)?

I think that mixture screw is around one turn, or so.

Thanks for your help.

Have a nice day.

Klemen
klemen-SLO is offline  
 
September 4th, 2007, 01:21 AM   #2
Senior Member
 
Joined: Oct 2006
From: Vienna-Austria-Europe

Posts: 210
Thanks: 1

I Ride:
RE: Carburettor settings

Klemen-slo,

look into the owner-doc/carburation/dellorto
Everthing there
Gokai134 is offline  
September 23rd, 2007, 10:19 PM   #3
Member
 
Joined: Mar 2007
From: Fresno, Ca. USA

Posts: 36
Thanks: 0

I Ride:
Re: RE: Carburettor settings

Originally Posted by Gokai134
Klemen-slo,

look into the owner-doc/carburation/dellorto
Everthing there
Almost. Sometimes the simple is overlooked ... Which direction leans the polit/starting circuit is not there. Could this be added to the doc?
montibank is offline  
September 24th, 2007, 03:18 AM   #4
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 15,548
Thanks: 419

I Ride: Husaberg FE501e 2003
RE: Re: RE: Carburettor settings

the screw is i believe an air bleed screw so the more open you screw it = the more air enters to make it leaner.

i believe the doc dopes explain how to set the carb by ear for the first time which is how you should do it anyway (ideally).

to recap:
get it running
adjust air screw to gain highest idle
lower idle to correct rpm of 1,800rpm.
adjust air screw again
adjust idle screw again for 1,800rpm (or abouts)
test ride noting any 'bog' and adjust the air screw to eradicate this. it should take about 1/4-of-a-turn either way.

regards

Taffy
Taffy is offline  
September 24th, 2007, 05:56 AM   #5
Senior Member
 
Joined: Mar 2005
From: Mesa, AZ

Posts: 2,713
Thanks: 3

I Ride:
RE: Re: RE: Carburettor settings

If you go to the download section at www.husaberg.se, you should be able to print the old parts manual. At the end, it tells you how many turns out for the idle and the mixture screw. Usually around 5 out (+/- 1) for the idle and between 1 1/2 and 2 out for the mixture.

Then what Taffy says.

Check the download section on this site, for the 4 videos. I think the first one shows how to adjust mixture and idle.
LeFrog is offline  
September 24th, 2007, 11:53 AM   #6
Senior Member
 
dsducati's Avatar
 
Joined: Apr 2004
From: Arizona

Posts: 518
Thanks: 0

I Ride:
Round slide Dellortos use a fuel mixture adjusting screw and flat slide Dellortos use the air bleed adjusting method.
dan
dsducati is offline  
September 24th, 2007, 12:01 PM   #7
Senior Member
 
Joined: Nov 2001
From: Ely, England

Posts: 15,548
Thanks: 419

I Ride: Husaberg FE501e 2003
i really must try and remember that. infact i'll go check the doc now coz if it's wrong in ma hea you know it'll be wrong in the doc!

ah! i had it right in the doc it's jus ma hea that needs a sortin oot!

regards

Taffy
Taffy is offline  
Reply

  Husaberg Forum > Husaberg Forum > Husaberg

Tags
carburettor, settings



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Map Switch Settings nobrakes Fuel 21 May 6th, 2012 06:49 AM
jet settings for MX (husaberg TE 300) tweetakt Mechanical 13 August 4th, 2011 02:47 AM
Fork Sag settings The_Force Suspension 5 November 25th, 2010 05:21 PM
Carburettor for FE 600 1998 model Chichor Fuel 4 December 1st, 2006 10:05 AM
Carburettor for my FE 600 1998 model Chichor Fuel 13 November 23rd, 2006 03:44 PM


Facebook Twitter Google+ RSS Feed