Husaberg Forum

Husaberg Forum (http://husaberg.org/husaberg-forums.php)
-   Husaberg (http://husaberg.org/husaberg/)
-   -   water pump bearing 2001 dimensions (http://husaberg.org/husaberg/25515-water-pump-bearing-2001-dimensions.html)

raygamache January 10th, 2019 01:52 PM

water pump bearing 2001 dimensions
 
Hi to all,
Could someone share the dimensions of the water pump bearing, I am hoping to order the bearing prior to pulling the bike apart.

Thank you

Ray

raygamache January 10th, 2019 05:56 PM

found the dimensions
 
Ok I was able to locate the dimensions, for anyone else in need of bearing the dimensions are 32mm OD, 10mm ID and 12mm width you want an open bearing part number 6201/C3 I found an SKF brand for 4.99 with free shipping

husabutt January 10th, 2019 06:31 PM

The water pump bearing is proprietary to Husaberg. It has a seal attached to it on one side.

Perhaps you can reuse your seal or find something similar.




Year/Model: 2004,
Component: CLUTCH COVER
Item #: 63
Part Number: 0625062013
Description: BALL BEARING SPEC.B.B.SKF 6201
Price: $35.63

raygamache January 10th, 2019 07:25 PM

bearing
 
Does the 2001 have that seal attached? The drawing does not show.

VOR165 January 10th, 2019 07:30 PM

Yes it is attached. If I am not mistaken, Taffy may offer a replacement. Check his site.

tourist January 11th, 2019 01:09 AM

It is humbly advised to shop around, as with anything.

husabutt January 11th, 2019 09:09 AM

Taffmeisters does sell a complete water pump seal kit for a bit more than you can purchase just the bearing alone in the U.S.

It includes all the parts that should be replaced.

Taffmeisters - Husaberg, KTM, Husqvarna, Gas Gas, dirt bikes - servicing, tuning, rebuilds, parts

Be sure to press the seal in. Don't try and knock it in with a hammer and socket.

Taffy January 11th, 2019 10:43 AM

yes, I have that bearing as an OEM and aftermarket part Ray. in stock. as I'm aware it is only used on the Husabergs.

cheers

Taffy

raygamache January 11th, 2019 02:53 PM

thank you
 
Taffy,
Thank you for replying and the auto decompression part I recently purchased from you has worked great! I will try to get on your site tonight.

ede January 11th, 2019 03:20 PM

4 Attachment(s)
Hi,

the bearing is a little special, but not proprietary to Husaberg. As far as I know it also could be found in laundry machines...

To avoid mixing water with oil, there is a shaft seal ring (see pic 1, on the water side), the seal on the bearing (see pic 1 on the oil side), and an additional O-Ring on the waterpump-shaft to provide a sealed surface between shaft and the inner ring of the bearing. So far that's it.
If you have problems with the weep hole, change all of them to be safe.

Make sure you push the bearing all the way in the cover. Don't worry, the bearing is a little more wide than the pocket. That's o.k.
If it's a tight fit, use a hot air fan to heat up the cover a little bit, or additional cooling spray for the bearing...

As an additional tweak I used an O-Ring with 0.2mm bigger diameter to get a tight fit between inner ring of the bearing and waterpump shaft.

Don't use any sealing silicone - it will find it's way into the oil system, clog the oil filter or tiny little holes (e.g. crank shaft...)!!!

The Bearing is: SKF ICOS D1B01-TN9/C3 (including seal)
Shaft seal ring: 10x18x4 BSL
O-Ring: 10.0 x 1.3 NBR 70 SH (original, 70 shore)
O-Ring I used: 10.0 x 1.5 NBR 70 SH (KTM order code: 0770010015)

Regards,
EDE


All times are GMT -8. The time now is 07:22 PM.

Copyright © 2019 Husaberg Forum. All rights reserved.