Husaberg Forum

Husaberg Forum (http://husaberg.org/husaberg-forums.php)
-   Husaberg (http://husaberg.org/husaberg/)
-   -   Husaberg fs650 2002 model rebuild (http://husaberg.org/husaberg/17072-husaberg-fs650-2002-model-rebuild.html)

Dawson 2583 October 12th, 2013 03:41 AM

Husaberg fs650 2002 model rebuild
 
Hi has any on got a link to were I can get a rebuild manual for a 2002 husaberg FS 650 ?

Cheers

plumbbob October 12th, 2013 08:46 AM

Re: Husaberg fs650 2002 model rebuild
 
Hi Dawson,

There's a section on stripping and rebuilding in the owners docs on the top left of the home page. :D

Dawson 2583 October 12th, 2013 09:17 AM

Re: Husaberg fs650 2002 model rebuild
 
Thanks ill have a look and print it out if I can
Much apresated all you guys are very help full much apresated

Goin be first time I've actually striped a 4 stroke down ive only striped 2 strokes down , got a lot ov friends that can help me so wish me luck :wink:

plumbbob October 12th, 2013 09:32 AM

Re: Husaberg fs650 2002 model rebuild
 
Apart from reading all the docs etc I took loads of pics as I stripped it down just as a reminder when it all goes back together.
Should be fine as long as you keep your mates coffee cups full!

Dawson 2583 October 12th, 2013 09:46 AM

Re: Husaberg fs650 2002 model rebuild
 
Haha yea keep the brews coming ! And cheers for the photo ideas oll do that to ! :mrgreen:

Dawson 2583 October 30th, 2013 01:58 AM

Re: Husaberg fs650 2002 model rebuild
 
This husaberg is not goin beat me but might bankrupt me ! :? Got it all striped down took crank out to check bearing an replace then noticed the f**kin Conrod is bent ! Aaaaaaaaaaahhhhhhhhhhhh! Out else ?

Kayeffess October 30th, 2013 02:13 AM

Re: Husaberg fs650 2002 model rebuild
 
That's unfortunate. Hopefully the crank is ok. I recently picked up a spare crank/rod/piston for my 01 off eBay ...mind you, I've been watching for something like this for 2 years. I like to have spares just in case. Good luck on the repair. How about some photos and a rebuild thread to help us pass the time.

Taffy October 31st, 2013 11:47 AM

Re: Husaberg fs650 2002 model rebuild
 
where are you from Dawson?

if it is a little bent it can be straightened. I've done - or should I say - had it done before.

Taffy

Dawson 2583 October 31st, 2013 12:47 PM

Re: Husaberg fs650 2002 model rebuild
 
Hi taffy it well bent , I would put picture on but for some reason it won't let me put pics on here
I'm from County Durham , I spoke to you about my cylinder head getting fixed and a few other parts ,

Taffy November 1st, 2013 01:31 AM

Re: Husaberg fs650 2002 model rebuild
 
rod kits are about 320gbp. then you have to have the crank split and pressed and straightened which is a 55-70gbp touch. then really, they have poor little ends and that ought to be done as well. I do a bush 15 quid cheaper than OEM at 25gbp. would you believe even I get them pressed in! they are so soft on the rim that they always burr and then I make an ugly repair so now I get that paid to be done as well!

these aren't cheap!it is nearly as cheap to find or buy a brand new 2005-8 pork chop crank at about 580gbp complete, then sell your old crank off. about evens I'd say and the satisfaction of knowing you have the better crank.

regards

Taffy


All times are GMT -8. The time now is 04:48 PM.

Copyright © 2020 Husaberg Forum. All rights reserved.